Share
Results 1 to 4 of 4

Thread: Welding Stand

  1. #1

    Default Welding Stand

    This will be the first project with my little welder, kind of a corny project but something I can use right now.

    I picked this piece of 3" tube, with a 8"x8"x3/8" plate on each end.



    I got this from SIMS surplus at $0.65/lb. It weighs about 30 lbs, but they felt sorry for me and gave it to me for 20 lbs. LOL

    Then I got this piece of 5/8" plate, it's 11.5" x 12". It may weigh about 20 lbs also, I'm not exactly sure.



    I'm just going to stick weld it using 7018. A bit late for stick welding so will do that tomorrow, I need to do that outside.

    I will use this mostly for practice, but can use it for a small welding stand.

    I'll add a couple pics after I weld it tomorrow.

    Alan
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	welding-stand-pedestal.jpg 
Views:	3926 
Size:	121.0 KB 
ID:	13665   Click image for larger version. 

Name:	welding-stand-pedestal-plate-on-top.jpg 
Views:	2450 
Size:	117.2 KB 
ID:	13666  

  2. #2

    Default

    Quote Originally Posted by aland View Post
    Well, I am a bit embarrassed to say I took a wire wheel to this stand and since there was only 4" difference in the plate, I just used it as-is.

    I need a better place to weld, and have some ideas, but this will work in the meantime.

    I ran some beads with 6013, 6011 and 7018.

    6013 was easier for me than the 6011, and my friend kept telling me, "Just let me know when you're using 6011 so I can keep clear...".

    7018 was the most solid looking bead to me. I didn't take any pics...

    We also tried some hf start tig and welded up 2 pieces of mild steel that he was using for a t-nut on a South Bend lathe. I would have milled it from solid, but it worked to weld it.

    Alan

  3. #3

    Default

    Still practicing with stick, and will be doing more tig practicing ASAP.

    Went over to the local metal yard and went binster diving through the cut-off bin...

    Have about 45 lbs. I got for $30. Most all of this is cold finish, except for the angle which is hot rolled. AFAICT there is no cold rolled angle, only tube and flat.

    Hard to see but I got a few small pieces of plate in the back that are cold finish.



    Alan

    PS - I should add that I've been pondering the small welding table which I had started this thread for, but have since changed my mind. There are 2 things I really need, a welding cart and a welding table. Seems to me that the Certiflat 2'x3' ProTable for $200 will be a good investment, and I can make a stand for it. I just don't think I can even get close by spending $100-$150 and it would require quite a bit of work which wouldn't get me as decent of a table. As such I have decided that I will buy the Certiflat welding table and build a welding cart. I have most of what I need for the cart, I just need to get a couple solid wheels to use on the rear, I have a couple casters I can use for the front. I'll be making a single bottle cart, 12" x 28" on the bottom, and 12" x 18" for the top shelf which will hold the welder.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	binster-diving-at-metal-yard.jpg 
Views:	1592 
Size:	96.5 KB 
ID:	13692  
    Last edited by aland; 01-25-2018 at 06:42 AM.

  4. #4

    Default

    Boy Alan I have a big ole heavy vice that would work well on your first piece you bought ( pipe with plates on both ends) might have to make the base a little larger. I have to make a weld cart also, I was going to revamp my cart I use for my plasma torch for the torch and the 255 but once I started reading in the 255 manual it said that the 255 needed about 18" on each side for cooling so this axed that so its back to the drawing board.

    Mark
    Garage stuff

    Everlast 255 EXT

    Miller 251 mig
    30A spool gun

    Miller 211 mig

    Lincoln SP 250 mig

    Lincoln buzz box

    Thermal Dynamics
    Pakmaster 75XL plasma

Similar Threads

  1. What does CV and CC stand for?
    By RoatanBill in forum Pre-sales, Sales and Shipping questions
    Replies: 1
    Last Post: 02-26-2016, 05:50 PM
  2. (Another) Band Saw Stand
    By its_34 in forum Other Custom Fabrications
    Replies: 24
    Last Post: 08-17-2013, 03:27 AM
  3. Replies: 10
    Last Post: 12-31-2012, 11:41 PM
  4. NATIONAL WELDING EQUIP old 3 TORCH TIP STAND...I.D. sought
    By sandwagon in forum General Welder Questions
    Replies: 1
    Last Post: 12-31-2012, 11:13 PM
  5. NEW STAND-OFFs S45 and P80
    By Titan winch in forum Everlast Announcements, Contests and Promotions
    Replies: 11
    Last Post: 09-24-2011, 08:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •