Does the foot control still override the panel amperage?
Does the foot control still override the panel amperage?
The foot pedal does override the panel setting, so I need to learn a little more about heat. I'll have to check if the display shows the amperage I'm running. This is a "by the seat of your pants" type unit. AC frequency, balance, pedal amperage, are all set by feel, but for less than a $1000 bucks I think it's just fine.
I believe it is by far the most tig for the money for ac welding. I need a 110 welder for parts of the shop without 220, but that little quirk with the foot control has kept me from buying one.
The newer units I believe have a rheostat that's adjustable on the pedal if you buy the pedal. This is the same way that the new TA's and "someother" brand works as well. Not a quirk, but just a feature of a lower priced welder. IF it is as you say, and want a panel control and won't buy the 185 because of it, then simply get the the 200DV. It's got panel amp adjustment, but you pay for it.
Mark
performance@everlastwelders.com
www.everlastgenerators.com
www.everlastwelders.com
877-755-9353 x204
M-F 9am - 5pm EST
I know that Everlast listens to what their customers say, I can see that by looking at the newer models such as the potentiometers on the front panels would get loose from the plastic wrapping during the boat ride, so they put a plastic protection door on the front panel to stop that. Some did not like the small high frequency start on the 250ex, so they replaced it with one that looks to be good for about 10,000 amps and the list go's on and on.
I do not mean to complain, its just I think this one little change with the foot control would make them just as popular as the 250ex, and most people on here already know what I think of it. The 185 has too many of the most wanted options to by thrown in with and be considered a cheap welder. IMO
I just wanted to be heard, I will not bring it up again.
Well, I just bought both the pedal and the unit and there is no rheostat. The panel override is not really an issue with a good pedal. But, if you do go with the cheaper pedal, amperage control swings quickly from one end to the other and requires a finer touch.
The AC frequency and balance settings are a bit of a challenge as there are no mid-range markings. Knowing these exact settings, like on the digital units, is a nice feature but hardly mandatory. In the end, you still have to run it to see if it's right or not and then make adjustments if necessary. There's no getting away from this, even with a Dynasty 350DX. But once you have the precise settings figured out it's nice to be able to call them right up, this is the advantage of the more expensive systems.
Did you buy an SSC? They don't have the control on it.
Mark
performance@everlastwelders.com
www.everlastgenerators.com
www.everlastwelders.com
877-755-9353 x204
M-F 9am - 5pm EST
Yes, it is the SSC pedal and is very nice. Highly recommend. The tape idea is good. I was just going to take a Sharpie and do little tag'n.
Using my 250EX, try to match audible frequency. But, I'll play with it before I get too anal about this. A good welder should be able to set-up, and any critical chit deserves test pieces prior to the real deal.
I want this machine to provide a good stable arc and consistent performance, all the rest is up to me. Been busy and not able to do anymore testing, but maybe tomorrow.
Thanks for your input, appreciate it!
Everlast 200DX
Everlast PT185
Shoptask 3-in-1 (not currently in my garage, but I own it...)
Any day on a motorcycle like this that ends just needing parts and labor is a good day.
4.82, 158.67mph 1/8th mile 7.350, 200.35mph 1/4 mile
Are you sure what you are trying to weld is aluminum?
Post up a picture of the weld along with an overview of your welder settings.
Everlast 200DX
Everlast PT185
Shoptask 3-in-1 (not currently in my garage, but I own it...)
Any day on a motorcycle like this that ends just needing parts and labor is a good day.
4.82, 158.67mph 1/8th mile 7.350, 200.35mph 1/4 mile