Powered plasma 60S...pulsing

[sticks]

Ironically I am having the same issue with my PP50, but only when I am at the 50 amp setting after about 10 seconds of cutting.

Air PSI is 75+, good ground, 5/8 mild steel 1/16 to 1/8 standoff. Not tripping the overload, and the problem goes away at 47 amps.

3 water separators/filters, Motorguard air filter/dryer, inlet pressure regulated at 85psi running (pressure drop from 90+ when trigger is pulled).

Not trying to hijack the thread, but it applies.

[everlastsupport]

Ironically I am having the same issue with my PP50, but only when I am at the 50 amp setting after about 10 seconds of cutting.

Air PSI is 75+, good ground, 5/8 mild steel 1/16 to 1/8 standoff. Not tripping the overload, and the problem goes away at 47 amps.

3 water separators/filters, Motorguard air filter/dryer, inlet pressure regulated at 85psi running (pressure drop from 90+ when trigger is pulled).

Not trying to hijack the thread, but it applies.

It sort of applies to this thread, but would have been better to start a new one as the PP60 and the PP50 use different torches. I run my PP50 about 65PSI and my PP60 I run at 72. Sounds like you have dry air, good flow, good ground. So I would experiment with the air pressure. Make sure consumables are good as well.

[sticks]

It sort of applies to this thread, but would have been better to start a new one as the PP60 and the PP50 use different torches. I run my PP50 about 65PSI and my PP60 I run at 72. Sounds like you have dry air, good flow, good ground. So I would experiment with the air pressure. Make sure consumables are good as well.

Will do. More air pressure for higher amps, or lower? Example - 20 amps - 65psi and 50 amps 70psi (more amps/more PSI)

[performance]

Actually, lowering the air pressure isn't the best idea for cutting. It can be done, but I have found that there is a better way and you will get better results... Downsizethe consumables for the amperage is a better way. The air pressure you cited is too much on the input side and on the operating side. You should be at 90 psi NO more on supply while static. Operating you should be no more than 73 or so (officially). You can buy smaller diameter holes for the PowerPlasma torch. The S-25 consumables will fit the S-45 and are designed for low amp cutting at the same air pressure.

Is the arc stuttering or going on and off completely?

[sticks]

Actually, lowering the air pressure isn't the best idea for cutting. It can be done, but I have found that there is a better way and you will get better results... Downsizethe consumables for the amperage is a better way. The air pressure you cited is too much on the input side and on the operating side. You should be at 90 psi NO more on supply while static. Operating you should be no more than 73 or so (officially). You can buy smaller diameter holes for the PowerPlasma torch. The S-25 consumables will fit the S-45 and are designed for low amp cutting at the same air pressure.

Is the arc stuttering or going on and off completely?

On and off completely.

And like a fool, I bought the 75pc consumable kit which are all the same size tips, #8 if I had to guess. I wish you guys had a variety pack of the 6, 8, and 10s.

I'll adjust the inlet pressure to 90, and verify my operating pressure at the torch is 73ish. When it acts up again, I'll tinker with the air pressure up and down to see if it goes away.

[broberts5]

My pp60s is at it again. Pulsing. Off and on. 73 psi. What gives? Any ideas?

[everlastsupport]

What torch do you have? Does it pulse with just firing the pilot arc?

I swapped consumables yesterday and had the same problem, in my case, I knew the air was dry and PSI was fine. Turned out, the new electrode was bad (maybe I did not get it tight). Swapped it and finished the job. Look at the electrode, make sure there are not burns on it.