Share
Page 1 of 2 12 LastLast
Results 1 to 20 of 23

Thread: NEW 2013 EVERLAST PowerITig 200T DC DIGITAL PULSE TIG WELDER LOW 2AMP START !

  1. #1

    Default NEW 2013 EVERLAST PowerITig 200T DC DIGITAL PULSE TIG WELDER LOW 2AMP START !

    One final announcement that we have to post up about the 2013 models...Another digital unit.

    One of the best niche units we have in our stable is the i-TIG 200. It's found a big following by guns smiths and other specialty manufacturers. It's a reliable, hard working unit with a LOT of capability.

    So we have considered what we can do to make a better product and improve performance and features. So we have developed a completely new I tig 200, which will fall into the digital lineup of welders that we have. It'll have similar features as the 255 EXT but as the i-tigs are DC only, it too will be DC only.

    ONE very special thing it will have is the ability to fire off at an incredible 2 amps. We've studied the market and found that there is a need for this extremely low ignition point for guys that have molds and similar products to repair. It's been a constant request, so we've added this major capability to the unit.

    Here are some comparative specs next to the current i-tig...

    Model Power-ITIG 200 Power-ITIG 200T
    Input Voltage 110/220V 50/60 Hz 220 V 50/60 Hz
    Rated Output 200 A 200 A
    OCV 60-80V 60-80 V
    Duty cycle 35%@200 amps 35% @ 200 amps
    Welding range 5-200A TIG 5-160A Stick 2-200 A TIG 2-160A Stick
    Arc Force 0-10 1-100
    Pulse amps 5-95% 2-200 amps
    Start Amps 15 A fixed 2-150 A
    End Amps 15 A fixed 2-150 A
    Up/Down Slope time 0-5 Seconds 0-25 Seconds
    Pre Flow Time 0-5 Seconds 0-5 Seconds
    Post Flow Time 0-5 Seconds 0-25 seconds
    2t/4t yes yes
    Hot Start arc amp (stick) No welding amps + 1-100%
    Hot start arc time No .1-1.5 Seconds
    Inverter Frequency 27khz 50 khz
    Anti stick function no yes
    memory no 0-9
    weight 16 kg 9.8 kg
    dimensions 425x195x310 mm same
    Protection class IP21s IP21s

    Click image for larger version. 

Name:	CaptureI200T.jpg 
Views:	628 
Size:	16.5 KB 
ID:	9719
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	digital itig 200.jpg 
Views:	557 
Size:	132.3 KB 
ID:	9718  
    Last edited by performance; 03-09-2013 at 04:13 AM.

  2. #2
    Join Date
    May 2012
    Location
    Disneyland
    Posts
    2,661

    Default

    Great looking little DC machine. I love the specs, but am sorry to see you dropped the dual input voltage. For the real low amp stuff, running on 120V can be pretty handy at times. Is this going to replace the current iTIG 200 or is this an additional model?
    Long arc, short arc, heliarc and in-the-dark!

  3. #3

    Default

    Quote Originally Posted by Rambozo View Post
    Great looking little DC machine. I love the specs, but am sorry to see you dropped the dual input voltage. For the real low amp stuff, running on 120V can be pretty handy at times. Is this going to replace the current iTIG 200 or is this an additional model?
    Rambozo

    dual voltage will be available in summer
    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

  4. #4

    Default

    Quote Originally Posted by Oleg View Post
    Rambozo

    dual voltage will be available in summer

    I don't think we are dropping it.

  5. #5
    Join Date
    Oct 2011
    Location
    Litchfield Park, AZ
    Posts
    370

    Default

    ~22 lb welder, looks like a nice compact unit with some great new additions.
    Miller 252
    PowerTig 250 EXT
    Evolution Rage 2
    48X6 inch Belt Sander w/ 9 inch Disk Sander
    ...

  6. #6

    Default

    When will these be available?
    Lincoln Eagle Engine Drive
    Everlast MTS 250
    Everlast Power Tig 225lx
    HTP Mig 2400
    Everlast Power Plasma 60C --> Just need to finish my CNC Plasma Table!
    Miller Spectrum 375 Extreme Plasma cutter
    Victor cutting torch
    HF 20 Ton Shop Press
    HF 4x6 Band Saw
    HF Air Compressor
    Northern Tool Drill Press


    www.murphywelding.com

  7. #7

    Default

    Quote Originally Posted by SeanMurphy265 View Post
    When will these be available?
    in stock !
    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

  8. #8
    Join Date
    Oct 2011
    Location
    Litchfield Park, AZ
    Posts
    370

    Default

    Quote Originally Posted by Oleg View Post
    in stock !
    What is the price?
    Miller 252
    PowerTig 250 EXT
    Evolution Rage 2
    48X6 inch Belt Sander w/ 9 inch Disk Sander
    ...

  9. #9
    Join Date
    Feb 2013
    Location
    Corner of "No" and "Where"
    Posts
    46

    Default

    Minor suggestion - You guys need to loose the nylon carry strap on your smaller units. I'd stick with a rigid handle (going to make one for my PP 50). I don't know of all that many people that would be toting these around like a man purse.
    Sticks
    Field Service Tech for a Concrete Paving Company
    Location: The corner of "No" and "Where"

    "If they break it, we will fix it"

    AKA

    "Find some scrap and build a new one"

  10. #10

    Default

    A good many people do actually and several companies use them. Changing to a handle type face cost MAJOR money to recast a panel.

  11. #11
    Join Date
    May 2012
    Location
    Disneyland
    Posts
    2,661

    Default

    Quote Originally Posted by sticks View Post
    Minor suggestion - You guys need to loose the nylon carry strap on your smaller units. I'd stick with a rigid handle (going to make one for my PP 50). I don't know of all that many people that would be toting these around like a man purse.
    An easy solution is to pop open the fixed end of the strap and rethread it back and forth a few times through the buckle. Then you have a nice handle sized strap that stays out of the way, and you could still make a shoulder strap if needed. I did that on my little PA140ST because the strap kept getting in the way. It works great and makes a nice handle.
    Long arc, short arc, heliarc and in-the-dark!

  12. Default

    With the series of tests that I was doing on this welder over the last week I found very consistent arc starts using a 1/16" 2% thoriated tungsten at 3 amps with a amp draw of . 746 amps
    The 2 amp output as stated may show on a multi meter as being correct but the actual low amp is 2.9 amps
    Another really nice feature on this and the new 255ext will be the ability to use any foot pedal or amp control torch regardless of what pot value they use .
    Cheers
    EVERLAST CANADA
    www.everlastwelders.ca
    www.titanwinches.com

    905 637 1637

  13. #13

    Default

    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

  14. #14

    Default

    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

  15. #15
    Join Date
    Oct 2011
    Location
    Litchfield Park, AZ
    Posts
    370

    Default

    Quote Originally Posted by Oleg View Post
    Is that a 255 EXT in the back gound?
    Miller 252
    PowerTig 250 EXT
    Evolution Rage 2
    48X6 inch Belt Sander w/ 9 inch Disk Sander
    ...

  16. #16

    Default

    No, it's the 210.

  17. Default

    Perhaps... but the 255EXT IS sitting behind him on the bench in this vid:

    http://www.youtube.com/watch?v=EnCNIskL5fc

    So where are we at on the 255? The other thread is locked so you might expect questions popping up anywhere.

    Thanks,
    Jim

  18. #18

    Default

    He does have 255EXT ... not the final version
    finil version will be ready in few weeks
    Duncan will be testing it at the factory on MAY 15th
    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

  19. Default

    Thanks Oleg, that is a good update. I Look forward to his reports from the factory.

    Jim

  20. #20

    Default

    Any update on the 110v 220v itig200t i recall reading that it should be done around the end of summer.

Similar Threads

  1. new 2013 I-tig 200T
    By redstopgreen in forum Customer Testimonials
    Replies: 1
    Last Post: 01-16-2014, 05:26 PM
  2. NEW 2013 EVERLAST PowerTig 255 EXT AC/DC DIGITAL TIG WELDER
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 256
    Last Post: 12-13-2013, 09:48 PM
  3. NEW 2013 Everlast PowerMIG 210 and 200 MIG / TIG DIGITAL WELDER
    By Oleg in forum Everlast Announcements, Contests and Promotions
    Replies: 14
    Last Post: 02-10-2013, 01:13 AM
  4. NEW 2013 EVERLAST PowerTIG 185 ACDC TIG / STICK WELDER
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 23
    Last Post: 12-24-2012, 12:43 AM
  5. NEW 2013 Everlast PowerMTS 200 MIG / DC TIG/ STICK WELDER
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 0
    Last Post: 11-22-2012, 02:20 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •