Share
Page 1 of 5 123 ... LastLast
Results 1 to 20 of 88

Thread: Hitachi G12SR3 4.5" angle grinder 6.0 amp

  1. #1
    Join Date
    Dec 2009
    Location
    Greater Seattle, WA
    Posts
    813

    Default Hitachi G12SR3 4.5" angle grinder 6.0 amp

    I recently picked up a few 4.5" Hitachi angle grinders (each model number G12SR3, rated 6.0 amp) refurbished. Got them from this vendor:
    http://bigskytool.com/Hitachi_G12SR3...d)___i967.aspx

    Click image for larger version. 

Name:	IMG_2016.jpg 
Views:	1069 
Size:	141.8 KB 
ID:	8793

    Click image for larger version. 

Name:	IMG_2017 (2).jpg 
Views:	1009 
Size:	152.6 KB 
ID:	8794

    So far, the Hitachi grinders seem to be decent. Compared to the Harbor Freight 4.5 amp "drill master" grinders that I'm most used to (which can be had for $10 with a coupon), the Hitachis run much smoother and quieter.

    I think a large part of the smoothness and quietness may be simply because the pinion gear is rigidly fastened/secured to the electric motor shaft (via threaded nut) on the Hitachi design:
    Click image for larger version. 

Name:	IMG_2002 (2).jpg 
Views:	1193 
Size:	133.6 KB 
ID:	8789

    In contrast with the above pic, the pinion gear dsign on the Drill Master "floats" on the keyed motor shaft. The floating gear apparently adds considerable rotational backlash, also imprecisely controlled gear clearance. I feel like it may be hard on the nearby bearing (I've already experienced one failure in this bearing in my fleet of Harbor Freight grinders.)

    The gear ratios are quite different between the different grinders (3.9 on the Hitachi versus 3.0 for the Harbor Freight), which would seem to help the Hitachi run at a slower, but more consistent speed. I was impressed by how much grease there was in the gearcases of these refurbished Hitachis:
    Click image for larger version. 

Name:	IMG_1997 (2).jpg 
Views:	2823 
Size:	143.2 KB 
ID:	8788

    The electric motors between the two different grinders are actually very similar in many respects (same diameter and number of poles, and number of commutator segments) but the Hitachi 6.0 amp motor is significantly longer than the 4.5 amp Drill Master motor. There is no epoxy encapsulation on the motor windings on either.
    Click image for larger version. 

Name:	IMG_2005.jpg 
Views:	1024 
Size:	136.4 KB 
ID:	8786

    The cooling fan design seems more sophisticated on the Hitachi (curved vanes with conical air diffuser) than on the Drill Master (straight blades and flat air diffuser), which may contribute to the reduced noise of the Hitachi.
    Click image for larger version. 

Name:	IMG_2001 (2).jpg 
Views:	1008 
Size:	144.2 KB 
ID:	8785 Click image for larger version. 

Name:	IMG_1998 (2).jpg 
Views:	1148 
Size:	140.3 KB 
ID:	8787

    The overall package of the Hitachi feels nice and it doesn't seem overly bulky, long, or cumbersome. However, the 6.0 amp Hitachi unfortunately does add on some significant extra weight compared to the 4.5 amp Harbor Freight.
    Click image for larger version. 

Name:	IMG_2009 (2).jpg 
Views:	824 
Size:	133.5 KB 
ID:	8790
    Specifically, the bare Hitachi weighs 3.3 lbs (versus 2.8 lbs for the bare Drill Master). And when the guard, handle, and disc retaining hardware are included, the weight of the Hitachi goes up to 4.6 lbs (versus 3.5 lbs for the drill master). The guard and disc retaining hardware seem overkill in terms of material thickness on the Hitachi.

    Although I don't expect to be able to put extra power to work on most flap wheel jobs that I often do (where the speed is usually limited by rate heat in the work can dissipate), I am looking forward to using it on jobs involving using a cutting wheel or disc grinder on thicker metals where the extra power might come in handy. I can see myself however reaching for the Hitachi most of the time, even if only because of how much quieter and smoother it is.

    -edit-
    Almost forgot to mention another sign of the Hitachi tool having quality is that the spindle lock button on the Hitachi works very accurately, with little slop. (The Drill Master spindle locking button has tons of slop, and racks sideways like crazy.)
    Last edited by jakeru; 12-11-2012 at 07:47 AM.
    '13 Everlast 255EXT
    '07 Everlast Super200P

  2. #2
    Join Date
    Nov 2012
    Location
    Cambridge, ON. CA
    Posts
    111

    Default

    Very nice and thorough review! I like Hitachi tools as I can get them cheap here too and their quality can justify the price difference. Unfortunately I don't have a Hitachi small grinder yet. Doing the duty right now is a 4" Powerfist angle grinder. The Canadian equivalent of your HF Drill Master brand I'm think. It's so compact that it'll fit in the carrying case that came with my PA140ST. That's handy! So far it hasn't be lacking power but it's a bear to work with due to the noise and ergonomics.

    Can we see the 2 units side by side? How do they compare in size and ergonomics.
    PowerArc 140ST
    Victor VPT-100FC

  3. #3

    Default

    I read a lot a reviews on impact drills. They scored high there too. Wouldn't surprise me their grinders are really good.
    Mike R.
    Email: admineverlast@everlastwelders.com
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

  4. #4
    Join Date
    Oct 2010
    Location
    Northern Virginia
    Posts
    1,323

    Default

    You must have bought the last one, Jakeru, that link shows they're out of stock! Excellent review with tear-down views, thanks. That looks like a good place to bookmark for future purchases.
    DaveO
    Oxweld oxy acet gear
    IMIG 200
    PowerTIG 210 EXT... Amazing!

  5. #5
    Join Date
    Mar 2011
    Location
    Eastern Oregon
    Posts
    681

    Default

    Interesting that the title says 6A, but the description and specs list it as 5.0
    Penncrest Buzzbox - Infinite amp control! Man the 70's were good.
    Everlast Powerplasma 60 - Reliable unit, cuts well.
    Everlast i-MIG 250P w/spoolgun - Really smooth, plenty of cajones.
    Everlast 250EXT - Sometimes it just takes a kick in the balls...
    Everlast 255EXT - Just started playing

  6. #6
    Join Date
    Dec 2009
    Location
    Greater Seattle, WA
    Posts
    813

    Default

    Thanks for the feedback, guys; I'm glad you found this product review to be useful! In due course, I'll make sure to update this thread with longer-term results as well.

    Tanh - I'll get some comparison pics with the Harbor Freight grinder. (Maybe I will start another thread to fully and "properly" review the Drillmaster grinders.)

    DaveO - I put my order in on these during a "cyber monday" sale at bigskytools, where the "A" refurbished grade for this grinder (which is what I got) was on sale for about the normal cost of a "C" refurbished grade. Bigsky has an e-mail notification feature where they'll e-mail you when they get more in stock (click the "notify me when it's available" link).

    Brand new on Amazon, the same model grinder goes for $40 shipped.

    Redbeard - Some of the specifications on bigskytools (the amp rating, as well as the no-load speed) appear incorrect. Here are the specs directly from Hitachi North America, which should be more reliable.

    The nameplate on the actual grinder indicates 6.0 amps and 10,000 RPM. Also, based on my actual test results, the 3.1 pound weight specification is inaccurate (and IMO, borders on misleading.)
    Last edited by jakeru; 12-12-2012 at 08:57 PM.
    '13 Everlast 255EXT
    '07 Everlast Super200P

  7. Default

    I'm really not a fan of the HF grinder so I may have to give the Hitachi a try when this one quits the bed. The slower speed will be nice but I'm more looking forward to the quieter operation. Even without touching the HF one to metal its ear peircing loud and just annoying.
    Poewr I-Mig 205P
    Powertig 185

  8. #8
    Join Date
    Dec 2009
    Location
    Greater Seattle, WA
    Posts
    813

    Default

    Just wanted to give an update that I put the Hitachi 6amp grinder though a tube cutting job where I had to make about 30 or so cuts in rapid succession through some 1.5" diameter mild steel downspout type material (fairly thin gauge), but it was thick enough that I was able to press down fairly hard to make it go faster and see how the grinder would perform. I was impressed! It sure went through those cuts fast and the motor never did bog very much, even when pressing down fairly hard.

    By the end of the job (which only took a few minutes) the entire 4.5" cutting wheel had gotten consumed down to the nub! I think how quickly the Hitachi 6 amp can wear out the cutting wheel is telling of its power output. I've never seen that kind of cutting wheel wear on the 4.5 amp Harbor freight grinder.

    --UPDATE--
    I just noticed that it looks like BigSkyTool now has 44 of these grinders in stock now (in "A" grade, for $29 each + shipping).
    Last edited by jakeru; 12-24-2012 at 09:46 PM.
    '13 Everlast 255EXT
    '07 Everlast Super200P

  9. #9
    Join Date
    Dec 2009
    Location
    Greater Seattle, WA
    Posts
    813

    Default

    For anyone look for a good deal on these grinders, now's a good time to jump:
    http://bigskytool.com/Hitachi_G12SR3...d)___i967.aspx

    "A" grade (top refurbished grade) is on sale right now for $27 shipped. This is a really decent grinder. If you're used to using the harbor freight $10 grinders, the smoothness of the Hitachi will blow you away.

    (I will consider actually have to consider stocking up on some more myself!)
    Last edited by jakeru; 06-21-2013 at 04:16 AM.
    '13 Everlast 255EXT
    '07 Everlast Super200P

  10. #10

    Default

    I have three of the paddle switch grinders from harbor freight. http://www.harborfreight.com/4-1-2-h...tch-65519.html
    One of them runs super smooth while the other two I would rate an 8 out of 10 because of slight vibration. Stay away from the HF grinding wheels... they don't grind, they only heat and polish.
    2013 250EX : SSC Pedal : I-MIG 250P 20' Profax gun : Power Plasma 60 p80 torch : 3M Speedglas 9100XX : Evolution Rage 3 DB cold saw

  11. #11
    Join Date
    Mar 2011
    Location
    Eastern Oregon
    Posts
    681

    Default

    Thanks for the heads up. Just ordered a pair to add to the fleet. I think I will now have more grinders than wheels
    Penncrest Buzzbox - Infinite amp control! Man the 70's were good.
    Everlast Powerplasma 60 - Reliable unit, cuts well.
    Everlast i-MIG 250P w/spoolgun - Really smooth, plenty of cajones.
    Everlast 250EXT - Sometimes it just takes a kick in the balls...
    Everlast 255EXT - Just started playing

  12. #12

    Default

    Quote Originally Posted by jakeru View Post
    For anyone look for a good deal on these grinders, now's a good time to jump:
    http://bigskytool.com/Hitachi_G12SR3...d)___i967.aspx

    "A" grade (top refurbished grade) is on sale right now for $27 shipped. This is a really decent grinder. If you're used to using the harbor freight $10 grinders, the smoothness of the Hitachi will blow you away.

    (I will consider actually have to consider stocking up on some more myself!)
    Thanks Jake. Will pick up two. I have 4 HF now, but will try a name brand at that price. I have one HF one that has to be around 10 years old. But the lack of a bearing or weird sleve, they are not smooth at all.

    Thank for sharing you find.
    Mike R.
    Email: admineverlast@everlastwelders.com
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

  13. #13

    Default

    Jake, it mentions safe slide switch. Does it have the switch you have to hold on?
    Mike R.
    Email: admineverlast@everlastwelders.com
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

  14. #14
    Join Date
    May 2012
    Location
    Disneyland
    Posts
    2,662

    Default

    Thanks for the heads up. I will give two a go, too. If it's anything like my DeWalt the slide switch is spring loaded but can also be snapped to a stay on position. I have DeWalts with both the slide and paddle, and I really prefer the slide. With heavy gloves on, the safety on the paddle is a pain, and If I take the safety off, I can't hardly set the thing down without it going off. If I have a cart or someplace to hang it up, I like the paddle, but for crawling around, over, under, and through stuff, the slide is king.

    I love that it comes with a case, too.
    Last edited by Rambozo; 06-21-2013 at 01:29 PM. Reason: Might as well get two
    Long arc, short arc, heliarc and in-the-dark!

  15. #15
    Join Date
    Oct 2012
    Location
    Canada, Suttonwest, Ontario
    Posts
    676

    Default

    I have gone thru a lot of grinder in the shop and on the job site bought a good grinder 15 years ago and it is still working it is German made AEG Grinder WS 1200-125 Spec., 1200 Watts, 11,000 r / min, wheel diameter: 5 inch you cannot stop it, you can push as hard as you can and it will not stop it cost more but worth it in the long run, it probably has over 1000 hrs. on it changed brushes around 700 hrs. The HF (USA)and PA(CA) just go up in smoke in no time. they have been making the same grinder over 20 years just color changes.
    Click image for larger version. 

Name:	AEG-grinder-ws-1200-125.jpg 
Views:	688 
Size:	8.8 KB 
ID:	10134
    Everlast PowerTig 325EXT (Canada)
    Everlast Power I Mig 250 (Canada)
    Everlast PowerPlasma 80S (Canada)
    Everlast PowerCool W300 (Canada)
    Everlast PowerMTS 250S Fitted with a 30A Spoolgun(Canada)
    Miller Dynasty 400 wireless(Canada)
    Millermatic 252 plus 30A Spoolgun(Canada)

  16. #16
    Join Date
    Mar 2011
    Location
    Eastern Oregon
    Posts
    681

    Default

    There is one other plus to the $10 HF grinders (besides the fact that they ARE $10 grinders of course) and that is the return factor. If you use them hard and heavy, it shouldn't be too hard to wreck them within the 90 days. Not to mention the fact that the one I bought 10 months ago looks identical to the one I bought last week.
    Penncrest Buzzbox - Infinite amp control! Man the 70's were good.
    Everlast Powerplasma 60 - Reliable unit, cuts well.
    Everlast i-MIG 250P w/spoolgun - Really smooth, plenty of cajones.
    Everlast 250EXT - Sometimes it just takes a kick in the balls...
    Everlast 255EXT - Just started playing

  17. #17
    Join Date
    Dec 2009
    Location
    Greater Seattle, WA
    Posts
    813

    Default

    Quote Originally Posted by Rambozo View Post
    ... If it's anything like my DeWalt the slide switch is spring loaded but can also be snapped to a stay on position.
    Yep, that pretty much describes it. A slider that locks with a bit of a rocking motion, which you rock the other direction to make it turn off. Takes a few tries before getting totally used to, but works well and I can do it with a gloved thumb pretty easily.
    '13 Everlast 255EXT
    '07 Everlast Super200P

  18. #18

    Default

    Quote Originally Posted by Rambozo View Post
    Thanks for the heads up. I will give two a go, too. If it's anything like my DeWalt the slide switch is spring loaded but can also be snapped to a stay on position. I have DeWalts with both the slide and paddle, and I really prefer the slide. With heavy gloves on, the safety on the paddle is a pain, and If I take the safety off, I can't hardly set the thing down without it going off. If I have a cart or someplace to hang it up, I like the paddle, but for crawling around, over, under, and through stuff, the slide is king.

    I love that it comes with a case, too.
    Good point about the paddle. I was thinking about getting a paddle grinder but I never thought about safety and the paddle getting depressed. Grinders with slop physically wear me down with all of their vibration. I always wear ear plugs so the noise doesn't bother me (my neighbors though are a different matter though).

  19. #19

    Default

    Quote Originally Posted by redbeard View Post
    There is one other plus to the $10 HF grinders (besides the fact that they ARE $10 grinders of course) and that is the return factor. If you use them hard and heavy, it shouldn't be too hard to wreck them within the 90 days. Not to mention the fact that the one I bought 10 months ago looks identical to the one I bought last week.
    Well I bought 2 (will see what Jake sees soon; ground shipping free), 3 would have been better (cut, flap and grind). But not going to dump the OLD HF grinders all the way around (other can use them). Was a little over $58. My old orange HF one has to be 10 years or older, one set of brushes (that came with it) as I recall. Still uses to cut many times a week.

    I was in HF one time (I have been in there way to many times I can assure you) and I guy had about 5 broken, dirty grinders with the boxes. Covered in grind dust of some kind. They swapped him out and the guy had on a body shop shirt no less covered in the same looking dust So you are right there. I laughed inside when I saw him do it and with a straight face too.
    Mike R.
    Email: admineverlast@everlastwelders.com
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

  20. #20

    Default

    Re-read the OP, Jake you need to write for a couple magazines. Take it apart, weigh it, abuse it, review it. Or have a show on discovery channel.

    Did you get a second Everlast machine still using the Super 200P?
    Mike R.
    Email: admineverlast@everlastwelders.com
    www.everlastgenerators.com
    www.everlastwelders.com
    877-755-9353 x203
    M-F 12 - 7PM PST
    FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.

Similar Threads

  1. Best Nozzle for Close Angle Merged Exhaust Tubing?
    By Welderooni in forum TIG Welding (GTAW/GTAW-P)
    Replies: 12
    Last Post: 01-15-2013, 05:46 PM
  2. Optimal Tungsten Grinding Angle
    By Rivets in forum TIG Welding (GTAW/GTAW-P)
    Replies: 3
    Last Post: 06-11-2012, 09:49 PM
  3. cutting at an angle
    By McClary in forum Everlast Plasma Cutters (PAC)
    Replies: 4
    Last Post: 12-29-2011, 01:01 PM
  4. Cutting 3"x3"x3/16" Angle
    By NRM in forum Multi-Process Units (TIG,Stick,Plasma/MIG,TIG,Stick Combo units)
    Replies: 7
    Last Post: 07-02-2011, 12:56 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •