Share
Results 1 to 20 of 257

Thread: NEW 2013 EVERLAST PowerTig 255 EXT AC/DC DIGITAL TIG WELDER

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. Default

    Hi Mark,

    I have a couple of questions, and hope you can help with their answers. In using the 250ext, the interface was tricky because of the high "typematic" rate. You would overshoot your target, then go back with ten more button presses to hit it. I called it the interface of a thousand button presses, I know this was fixed in a repair release, but in the mean time, we all moved on to the 255 plans.

    My question is regarding exactly how the 255 interface works, if you know yet. Obviously there is some combination of knob presses, knob twists, probably short and long knob presses to enter modes to select functions and others to set values. So please describe:

    How do you enter the function-change mode?
    Do you press the knob to move through the functions or twist it?
    How do you get into value-change mode?
    How long, in seconds, do you ever need to hold in the knob?
    Is a quick press of the knob used? For what action?
    Does it always return to Amps? If so, do you then just twist the knob, or do you press, or tap, the knob then set the amps value?
    Please walk me through this interface once before it shows up, thanks.

    My second question is regarding the knobs. Oleg gave me hope earlier in this thread that you had found better knobs for the 255, is that so?

    Thanks for any info on this. I really hope this interface will be helpful to the operator, rather than cumbersome.

    Jim

  2. #2

    Default

    Jim,
    Not having my hands on the final test version yet, I can give limited answers.
    Duncan likely has more to say than I do. But its not unlike the 210 in this fashion.
    The main knob controls both the limits and the exact function. Simply tap the knob to set,and roll it to highlight and select function, then tap it again to adjust it. Roll the knob up or down to increase or decrease. Press again to lock in the function.

    There is basically only 1 knob on the ext. It wasn't on the ext units we were primarily working on different knobs...though it is a consideration.
    Last edited by performance; 03-28-2013 at 08:01 PM.

  3. Default

    Thanks Mark,

    If it uses quick taps, that's fine, it's pressing and holding for x number of seconds that I am not a fan of.

    My thinking on the knob is, since it only has one,and it is nearly the entire interface, let's make it a nice one Even the current 250EX amp knob is a bit nicer than the one shown in the photos of the 255. After all, this is your top-level entry in the US, right? Thanks for whatever you can do for us.

    Jim

  4. #4

    Default

    I don't have anything to do with that at this point. That detail would be for Duncan. He has his hands on the digital units in the factory. I have no idea. It will be whatever is available to fit the encoder that is used. They don't fit the same. To special make one would involve a lot of expense and planning.

    It'll likely be this knob or a cut down version of it:
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	CaptureI200T.jpg 
Views:	493 
Size:	16.5 KB 
ID:	9869  
    Last edited by performance; 03-28-2013 at 11:08 PM.

  5. #5

    Default

    Oleg Gladshteyn
    Phone: 650 588 8082 / 877 755 WELD
    Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
    Email: oleg@everlastwelders.com
    Website www.everlastgenerators.com

    www.linkedin.com/pub/oleg-gladshteyn/48/b08/875

Similar Threads

  1. NEW 2013 EVERLAST PowerITig 200T DC DIGITAL PULSE TIG WELDER LOW 2AMP START !
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 22
    Last Post: 04-12-2016, 08:15 PM
  2. NEW 2013 Everlast PowerTIG 200DX AC/DC TIG DUAL VOLTAGE welder
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 28
    Last Post: 03-04-2013, 02:23 AM
  3. NEW 2013 Everlast PowerMIG 210 and 200 MIG / TIG DIGITAL WELDER
    By Oleg in forum Everlast Announcements, Contests and Promotions
    Replies: 14
    Last Post: 02-10-2013, 01:13 AM
  4. NEW 2013 EVERLAST PowerTIG 185 ACDC TIG / STICK WELDER
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 23
    Last Post: 12-24-2012, 12:43 AM
  5. Mystery Welder Revealed: 2012 DIGITAL POWERTIG 210EXT TIG/STICK welder
    By performance in forum Everlast Announcements, Contests and Promotions
    Replies: 46
    Last Post: 07-28-2012, 02:19 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •