Share
Results 1 to 3 of 3

Thread: PowerTig 200DX Cover

  1. Default PowerTig 200DX Cover

    Here is a nice cover my wife reluctantly made for my PowerTig 200DX welder. It's made from dark green "Duck Canvas" from the local JoAnn Fabrics store. I believe I paid about $10.00 for the material which was on sale and is quite nice. I believe I purchased 1 1/2 yards.

    Dimensions for the fabric pieces:
    Quantity 2 Side panels 18" X 22.5"
    Quantity 2 End Panels 13.5 " X 18"
    Quantity 1 Top Panel 13.5" X 22.5"

    The above dimensions make a fairly roomy cover with about 0.25 inch for the seams and 1" turned under on the bottom edge.

    You can cut the two sides and two ends in one shot by folding the cloth in half and then splitting it when you are done. It's much easier to convince someone to sew the pieces together if you cut the pieces yourself!

    Click image for larger version. 

Name:	IMG_0889.JPG 
Views:	328 
Size:	111.3 KB 
ID:	3181

    Link to material:
    http://www.joann.com/joann/catalog/p...RODID=prd23683
    Last edited by earla; 08-27-2011 at 09:56 PM. Reason: Added link to material

  2. #2
    Join Date
    Mar 2011
    Location
    The Boonies of Texas
    Posts
    420

    Default

    Nice! Here is a thread about this very subject: http://www.everlastgenerators.com/fo...e-on-this-site......

    Thurmond
    Miller Bobcat 3 Phase,
    Miller Suitcase X-Treme 12VS wire feeder for the Bobcat with M-25 300A .045" gun / Bernard 400A 5/64" wire mig gun .
    26 series gas cooled TIG torch, setup for quick connect to Bobcat.
    17 series gas cooled Tig Torch for Low Amp Solar Tig (Direct Solar Panel Powered Tig welding)
    Hobart Handler 187 Mig / Fluxcore
    EVERLAST PowerUltra 205P
    EVERLAST PowerTig 250 EXT 2013 Model

  3. #3

    Default

    I would like to have one of those myself. I don't like the idea of my 200dx sitting out exposed. I tend to go a few weeks between uses. I worked for an Internet Service Provider in the late 90's and did computer repair all that fun stuff. Every time I worked on a computer in a shop it was always filthy inside. Not sure if it hurts anything, but I would feel better.
    Lincoln Eagle Engine Drive
    Everlast MTS 250
    Everlast Power Tig 225lx
    HTP Mig 2400
    Everlast Power Plasma 60C --> Just need to finish my CNC Plasma Table!
    Miller Spectrum 375 Extreme Plasma cutter
    Victor cutting torch
    HF 20 Ton Shop Press
    HF 4x6 Band Saw
    HF Air Compressor
    Northern Tool Drill Press


    www.murphywelding.com

Similar Threads

  1. PowerTig 200dx question
    By AnimalMother in forum TIG Welding (GTAW/GTAW-P)
    Replies: 6
    Last Post: 02-25-2016, 02:44 AM
  2. PowerTIG 200DX
    By Sparky_Mark in forum Pre-sales, Sales and Shipping questions
    Replies: 4
    Last Post: 10-18-2015, 05:09 AM
  3. PowerTIG 255EXT everlast branded cover?
    By ronmartin in forum TIG Welding (GTAW/GTAW-P)
    Replies: 2
    Last Post: 06-28-2015, 03:42 PM
  4. powertig 200dx problem
    By babowtie in forum Multi-Process Units (TIG,Stick,Plasma/MIG,TIG,Stick Combo units)
    Replies: 4
    Last Post: 02-01-2015, 05:30 PM
  5. Buy the Powertig 200dx or save for The Dynasty 200dx
    By AfroPaul in forum TIG Welding (GTAW/GTAW-P)
    Replies: 40
    Last Post: 05-13-2013, 08:18 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •