Last edited by Ray; 05-07-2012 at 05:50 PM. Reason: add spaces
____
Ray
Everlast Sales and Support Team.
support@everlastalaska.com
www.everlastalaska.com
877-755-9353 X207
____
Ray
Everlast Sales and Support Team.
support@everlastalaska.com
www.everlastalaska.com
877-755-9353 X207
http://www.facebook.com/CBRMetalworks
'96 Tacoma V6 on 37's, full custom, built for racin!
Yamaha Rhino w/ 800 Rotax built for racin!
Miller 251 MIG
Everlast Powerplasma 60C with CNC plasma table
Looking for sponsors for KOH 2013 race!
Racin' Tacoma Build Thread
Come on guys (everlast people), I am really starting to wonder about these 'good customer service' things people post. I have asked about this NUMEROUS times, via PM, phonecalls, etc. I am also missing the CNC port connector, which I called about a day or two after I got the plasma cutter, and have PM'd or e-mailed about to no avail.
What gives? I *think* #5 on the CNC port will work so long as I have a place to hook the (-) to that does not have a 100K resistor, but I don't want to go inside the unit and hook to something that would void the warranty.
It seems 2 weeks should have been plenty of time to figure this out....
http://www.facebook.com/CBRMetalworks
'96 Tacoma V6 on 37's, full custom, built for racin!
Yamaha Rhino w/ 800 Rotax built for racin!
Miller 251 MIG
Everlast Powerplasma 60C with CNC plasma table
Looking for sponsors for KOH 2013 race!
Racin' Tacoma Build Thread
have you opened it up and change the the divided arc on the ROHS cnc circuit board
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
It seems that the arc OK is the problem from what I have read on CNC Zone. You can jump the arc OK to keep it on all the time, which seems to be working fine. The other solution is something to read your voltages that can supply the arc OK externally. CandCNC sells this it runs around $85.00. This reads the voltage at the tip and makes adjustments.
I spent about 45 minutes on the phone with Eagle Plasma on Wednesday. He sells a THC that works externally, and is a generic THC so it works across the board it runs $250.00 (which is not what you need). This setup reads voltage at the tip and inside the machine.
I got a feeling since burn tables has a proprietary thc your probably going to have to open your plasma cutter and solder something. I would try jumping the arc ok (leaving it on) first to see how it works. From what I have read this means when the torch is through cutting a part it would move to the next part without having to wait on the arc OK to be triggered. johndjmix did this for his plasma table build and it worked form him.
Lincoln Eagle Engine Drive
Everlast MTS 250
Everlast Power Tig 225lx
HTP Mig 2400
Everlast Power Plasma 60C --> Just need to finish my CNC Plasma Table!
Miller Spectrum 375 Extreme Plasma cutter
Victor cutting torch
HF 20 Ton Shop Press
HF 4x6 Band Saw
HF Air Compressor
Northern Tool Drill Press
www.murphywelding.com
The Arc-OK is not the only problem, a problem yes, but not the only one. The main problem is the reading the plasma cutter puts out, even if I press the manual 'move' button, the ATHC does not hold to a correct height. The Arc-OK does not seem to work, which I don't think this is a problem with the Burntables control box, it is an issue with the plasma.
I still don't know why Everlast has not answered any of this, I guess if they don't know the answer they figure it is just easier to ignore it???? (PM's have been sent)--guess I will go try another PM...
http://www.facebook.com/CBRMetalworks
'96 Tacoma V6 on 37's, full custom, built for racin!
Yamaha Rhino w/ 800 Rotax built for racin!
Miller 251 MIG
Everlast Powerplasma 60C with CNC plasma table
Looking for sponsors for KOH 2013 race!
Racin' Tacoma Build Thread
if i want thc i am just buying the RAV-01 Raw Arc Volts Voltage Divider Card its only 42 dollars and tossing the one in my plasma would be easy to change since the everlast card has the pin connection labeled on the board . also checked out the DIGITAL CURRENT PROBE DCP-01 neat so you can see exact voltage also hers a pdf on these things nice instructions http://www.candcnc.com/PDF/DTHCII-se...stall-full.pdf
Last edited by Rodsmachineshop; 05-14-2012 at 04:45 AM.
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
yey Tacoma sorta pisses you off when never get a reply when need tech help . I feel the same way
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
Tacoma
PM me your number , will ask ray to u call u
Oleg Gladshteyn
Phone: 650 588 8082 / 877 755 WELD
Cell: 415 613 6664 ONLY IF YOU REALLY NEED IT
Email: oleg@everlastwelders.com
Website www.everlastgenerators.com
www.linkedin.com/pub/oleg-gladshteyn/48/b08/875
The digital current probe can supply you with the Arc OK signal. It reads the voltage at the work piece. It's a simple incompatibility issue that is causing you some problems. You do not need a different voltage divider with the DCP-01. From my understanding THC reads the voltage in two places. If you use something different to read the voltage it should give you the proper signal to make the height adjustments. That is why burntables is wanting you to install their voltage divider card inside your plasma cutter. If you use something that works externally from your plasma cutter to read the voltage and supply the arc ok signal you will not void your warranty.
Lincoln Eagle Engine Drive
Everlast MTS 250
Everlast Power Tig 225lx
HTP Mig 2400
Everlast Power Plasma 60C --> Just need to finish my CNC Plasma Table!
Miller Spectrum 375 Extreme Plasma cutter
Victor cutting torch
HF 20 Ton Shop Press
HF 4x6 Band Saw
HF Air Compressor
Northern Tool Drill Press
www.murphywelding.com
burntable wanted his arc divider set a 20:1 and the cnc board in the everlast only is 1:16 or 1:50 choices
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
Burntables didn't want me to do anything other than tap into the torch (+) with a 100K resistor, and the torch (-). I don't want to do any internal modifications if I can avoid it (might be different if it was not a brand new machine).
The Arc-OK should work, but doesn't seem to when I try to use the THC, but since the THC doesn't work at all, I want to get the THC functioning before I worry about the Arc-OK (because it may start working)
http://www.facebook.com/CBRMetalworks
'96 Tacoma V6 on 37's, full custom, built for racin!
Yamaha Rhino w/ 800 Rotax built for racin!
Miller 251 MIG
Everlast Powerplasma 60C with CNC plasma table
Looking for sponsors for KOH 2013 race!
Racin' Tacoma Build Thread
Why not ohm out from the torch - 100K pit to the end of the two 100Ks and when you get a short, that is the negative one. Then make a clip in jumper and jumper that one out. No real mods to the machine and gives them + with 100K and minus without. We are 1:16 and 1:50, some mod will have to happen to get 1:20 either way.
Mike R.
Email: admineverlast@everlastwelders.com
www.everlastgenerators.com
www.everlastwelders.com
877-755-9353 x203
M-F 12 - 7PM PST
FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.
for under 50 bucks i would just get the rav-01 card , but i would get matching connecter so you don't have to cut of the plasma cutter original connecters. then you would have more arc voltage settings . been searching the internet all the cnc sites and find a lot of guys have bought this card since there original card would not work , that what i am doing when i do my plasma cnc table . what would help us a lot if everlast would post the inside welders wiring schematics like most usa welders do so you know were all the pin outs are and were the wires lead to instead of having to rip the welder apart to see were connection start and end . just like my plasma the wires come out of card and then go under main circuit board so you can not see were they go and connect sorta stupid to me . trying to get my buddy that builds and dose electronics to come over and use his pin out test , its cool has all sorts of connecters that match plug the has a break out board to back ohm meter to see were they connect , will ask him how a divider card works he mite know hot to convert it to 1:20
Last edited by Rodsmachineshop; 05-14-2012 at 08:25 PM.
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
Last edited by Rodsmachineshop; 05-14-2012 at 09:18 PM.
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
Attachment 6648found out this diagram is wrong pulled my cnc arc divider card out of my everlast plasma cutter pin 5 is 2k instead of 100k but pin 7 is 100k its rite
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
If the two were reversed that would make his machine close to what the burntable people want in the first place. And the idea on the jumper would be shot in the foot as well if not 100K on both.
Rod, as I do not have this board and you do (well I have it, but I am not ripping my machine out of the rack and talking it apart). Maybe Ray can look or Oleg can mail me one. Rod can you ID the two resistors.
Better idea might be short them both out jumper clips (no mods to the machine that he is worried about) and add a 100K external to the control board line as needed?
Can you ID the resistor for 5 and 7.
Mike R.
Email: admineverlast@everlastwelders.com
www.everlastgenerators.com
www.everlastwelders.com
877-755-9353 x203
M-F 12 - 7PM PST
FYI: PP50, PP80, IMIG-200, IMIG-250P, 210EXT and 255EXT.
Last edited by Rodsmachineshop; 05-14-2012 at 10:30 PM.
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list
never jumper a resister can short stuff out adding more resisters ok but removing can fry components in a circuit board since like the relay on board is tied into some of the resisters . i think if he takes the 2k and replaces it with a 100k would fix his problem
EVERLAST 250 EX , EVERLAST I-MIG 205 , EVERLAST spool gun NOW have 2 EVERLAST POWER PLASMA 50 plasma cutter's , LINCOLN 175HD MIG WELDER , VICTOR TORCH SET and many more tools to many to list