Search:

Type: Posts; User: gasseous

Search: Search took 0.00 seconds.

  1. The 24 and the 30 has 1/4 input and output........

    The 24 and the 30 has 1/4 input and output..... but it has a nice bracket to mount it to the cart.....
  2. Not sure what the difference between the M-24 and...

    Not sure what the difference between the M-24 and the M-30 are.... (looking at the box).... I picked up the M-24 at the LWS and mounted it straight to my cart.... does anyone use this inline with...
  3. Replies
    12
    Views
    3,747

    I had a similar problem on my Super Ultra 205.......

    I had a similar problem on my Super Ultra 205.... my plasma cutter just stopped after about 10 inches of cut.... (the initial flame would come on but no cutting).... I rechecked my ground... no...
  4. Replies
    8
    Views
    2,896

    Zoama and Rambozo, I put in the 220v circuit...

    Zoama and Rambozo,

    I put in the 220v circuit and what a difference it makes.... now I don't blow the 20a breaker.... I also installed a Motor Guard filter at the back of my cart.... not sure what...
  5. Replies
    22
    Views
    7,091

    Zoama, Thanks for the advice. I noticed your...

    Zoama,

    Thanks for the advice. I noticed your guide and the attachment to your cutter. Did you make that? I have a spring like thing on the front of mine. Not sure if that is supposed to make...
  6. Replies
    22
    Views
    7,091

    Today I hooked up the air dryer and put my welder...

    Today I hooked up the air dryer and put my welder on a 220v circuit..... not sure if it is the dryer or the extra current, but what a difference.... I am still a little shakey on the plasma...
  7. Replies
    22
    Views
    7,091

    I purchased the M24 from my local welding store....

    I purchased the M24 from my local welding store. 1/4 in inlet / outlet..... 1 filter..... have not hooked it up yet, but am looking forward to doing so.... get my argon tomorrow, so I am just about...
  8. Replies
    22
    Views
    7,091

    Rambozo, I was thinking about going the water...

    Rambozo,

    I was thinking about going the water filter route.... I have a (3) filter setup for my reverse osmosis.... are you saying to remove the filter and fill the canister up with dessicant or...
  9. Replies
    22
    Views
    7,091

    Air Dryer Recommendation

    I have the Super Ultra 205 and am looking for a good air dryer. I went to Home Depot and looked at the dessicant dryers. They were all pink in the package. (They should be blue) I purchased (2) of...
  10. Replies
    8
    Views
    2,896

    130461304713048 Hopefully this will work.........

    130461304713048

    Hopefully this will work...... Just in case, the middle photo is with my Everlast pushed forward to allow the airline to clear the cart.....
  11. Replies
    8
    Views
    2,896

    Zoama, I do not know how to post a photo. If you...

    Zoama, I do not know how to post a photo. If you will send me a PM I can send you a photo. I found that I can get the airline straightened out sliding the entire unit forward. This may be the...
  12. Replies
    8
    Views
    2,896

    Thank you to everyone for the advice. While I am...

    Thank you to everyone for the advice. While I am planning on using this mostly inside the garage on 220V.... I can also see a real need to use it in the driveway on 110V.... (unless I either have...
  13. Replies
    8
    Views
    2,896

    Super Ultra 205 blows 20A 110v breaker

    I am new to welding. I have never used a TIG.... (I am waiting on a bottle of Argon so I am using the stick and plasma cutter) I have not ran a 220V circuit yet, but figure that this machine will...
  14. Replies
    9
    Views
    3,401

    Tonight I went out and increased my output...

    Tonight I went out and increased my output pressure to 80psi.... I was able to maintain 60 psi on the gauge on the front of the machine..... the plasma cutter would come on.... and begin to...
  15. Replies
    4
    Views
    1,642

    zoama, Thank you for the information. I am...

    zoama,

    Thank you for the information. I am getting some 3/32 tungsten.... just have not ordered it yet.... I need to get the Argon but was thinking of the #2 bottle.... mainly because of price but...
  16. Replies
    9
    Views
    3,401

    Rambozo, I realize that there is a pressure...

    Rambozo,

    I realize that there is a pressure gauge on the front..... I was having trouble obtaining 50psi on that gauge... I was curious what the pressure was going into the regulator.... I could...
  17. Replies
    4
    Views
    1,642

    Newbie in Hazel Green, Al

    Hello from Hazel Green, Alabama. I received my Super Ultra 205 yesterday and eagerly set it up. (I do not have any argon or tungsten so I was not able to use the TIG) I tried the stick welder and the...
  18. Replies
    9
    Views
    3,401

    zoama, I just received my SU205 yesterday. I...

    zoama,

    I just received my SU205 yesterday. I set it up like you did. However, my regulator did not come with the pressure gage shown in your photo. (I just have a plug to go there) Did you add...
Results 1 to 18 of 18