Search:

Type: Posts; User: JimMinKent

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    4,240

    Here's what Blue has to say on the subject: ...

    Here's what Blue has to say on the subject:

    http://youtu.be/U2_kWSG0RBg

    I don't have to do this very often but it's a good quick fix if you are helmet down and ready, and you get a misfire.
    ...
  2. I hope I am not misunderstanding what you are...

    I hope I am not misunderstanding what you are after, I am commenting as if you are asking about your truck chassis (frame) and not some type of ladder rack, or accessory frame. Here goes.

    You did...
  3. Replies
    7
    Views
    4,240

    This should get you on a safe path to success: ...

    This should get you on a safe path to success:

    Torch in Neg
    100% Argon at 8 LPM / 15 CFH
    About a #6 cup
    0.5 seconds Preflow to reduce initial blast
    6 seconds Postflow
    Balance 25%-30% of...
  4. Replies
    34
    Views
    19,881

    Wow, Very nice machine, Well done. Nice...

    Wow, Very nice machine, Well done. Nice accessories, too.

    I have one water-cooled 20F torch with that connector. In my 255 EXT, when snugged up, the water outlet ends up under the dinze,...
  5. Replies
    9
    Views
    8,111

    I didn't see this covered earlier in the thread,...

    I didn't see this covered earlier in the thread, but if you don't check the "Remember Me" box, it'll act like that.
  6. You are getting some good help from the guys...

    You are getting some good help from the guys here, I think you will be up and running right very soon.

    I think you can leave the actual values alone for now, since from what you describe, the pot...
  7. Search for "Power Pro tig pedal issues" There...

    Search for "Power Pro tig pedal issues" There were a few tweaks and fixes to these pedals covered there.

    http://www.everlastgenerators.com/forums/showthread.php/3643-Power-Pro-Tig-Pedal-Issues
  8. Replies
    1
    Views
    4,506

    I couldn't help myself...

    Once this stuff gets in your brain, there is nowhere you can run from it!


    Caulk Like TIG!

    11413

    11414

    and
  9. Replies
    1
    Views
    5,081

    I think this is a handy tip and it's unique to...

    I think this is a handy tip and it's unique to the 255 EXT, I wrote it up in my long post but it'll be easier to find here.

    I use the Pedal mode AND the 2T mode with the foot pedal. In Pedal...
  10. Replies
    26
    Views
    10,254

    Oh boy, you just got me thinking... With all...

    Oh boy, you just got me thinking...

    With all the timers on board the EXT, a guy should be able to spot weld, And We Can!

    For a say, 60 amp 2 second spot weld do this:

    2T mode
    AC or DC your...
  11. Replies
    26
    Views
    10,254

    I may have to set up an outlet and wire my pump...

    I may have to set up an outlet and wire my pump for 220. My machine is the early release with no rear outlet and the incorrect accessory package, (which should be on their way to us soon). It is...
  12. Replies
    26
    Views
    10,254

    I'll add the following and let you continue to...

    I'll add the following and let you continue to cogitate...

    As I said above, I am working with a difficult material, thin-walled home-store satin anodized aluminum tubing. Cannot use bumping...
  13. Replies
    26
    Views
    10,254

    Kempy, I ran into this several times yesterday...

    Kempy, I ran into this several times yesterday and then again today. I am building a device to assist a convalescing senior from 1" satin silver anodized aluminum tubing. This stuff is basically...
  14. Welcome, good to have you join the forum. See...

    Welcome, good to have you join the forum.

    See if it goes to 500 hz in DC pulse, your picture shows it in AC. My 255 EXT works correctly, and it pulses at 500 in DC and half of that in AC. 500 hz...
  15. Sticky: Kempy, That's a Great start!, You have a season...

    Kempy, That's a Great start!, You have a season of wonderful new experiences ahead of you.:D

    From the really small to the Really Big!

    11339 11338

    Keep us posted on your findings:)
  16. Replies
    58
    Views
    19,295

    Great news! Around here the gas is very well...

    Great news!

    Around here the gas is very well trusted, and the last thing I would suspect. This outcome makes sense, but I'd like to know just how wrong/contaminated gas can find it's way into a...
  17. Replies
    58
    Views
    19,295

    The consensus recognizes this is a shielding...

    The consensus recognizes this is a shielding problem.

    It could be very low gas flow.

    It could be a leak, drawing air into the gas stream.

    It could be tungsten sticking out past the...
  18. Replies
    58
    Views
    19,295

    Lets see if we can make some headway here. ...

    Lets see if we can make some headway here.

    Adding the water cooling won't weld differently, it will just keep your torch from a complete meltdown. Water cooled torches cannot handle very much...
  19. Replies
    22
    Views
    6,296

    Welcome nitris223:) Indeed you do, the...

    Welcome nitris223:)



    Indeed you do, the 255EXT single-phase I-max inrush current is 33.6a, operating current I-eff is 27a.

    The web page for the 255EXT is not yet updated, data from the...
  20. Replies
    5
    Views
    2,617

    Hello Braveops! You are pretty close, here's...

    Hello Braveops!

    You are pretty close, here's how I would start for STEEL:

    DC, 2T, No pulse
    Argon @ 15cfh/7LPM or slightly lower with #5/6 gas lens setup.
    Pre-flow = 1/2 sec.
    Post-flow = 5...
  21. Sticky: Thank You, yes it was indeed a Grand molten...

    Thank You, yes it was indeed a Grand molten puddle! These are really surprising discoveries. The "T" joint was a first try and so was this deep fusion. I'm just beginning to understand how this...
  22. Sticky: Part 2 of "Deep Fusion" Alright, let's have a...

    Part 2 of "Deep Fusion"

    Alright, let's have a look.

    11189

    I preheated with a MAPP gas torch, started in Section #1 and moved to the left. Filler is 1/8" 4043.

    11190
  23. Sticky: Gentlemen, I trust you are all up for another...

    Gentlemen, I trust you are all up for another "day hike" on our journey into the Unbelievable, so come along.

    As you will remember, I have been exploring the upper and outer limits of the 255...
  24. When you log in, select "Remember Me", it will...

    When you log in, select "Remember Me", it will put cookie on your machine and not boot you off every 5-10 minutes. I took me a while to figure that one out. Stick with us!
  25. Replies
    14
    Views
    4,259

    I would second Rambozo 's advice. I was on site...

    I would second Rambozo 's advice. I was on site in Wyoming with my Maxstar remodeling some institutional stainless kitchen sinks. While I was there they mentioned that they keep burning out the...
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4