Search:

Type: Posts; User: Buzz

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    177
    Views
    61,187

    I second Bill's comment, Its great to see all the...

    I second Bill's comment, Its great to see all the projects and the contests are a great motivator.
  2. Replies
    177
    Views
    61,187

    Congrats to all the winners and thanx a bunch for...

    Congrats to all the winners and thanx a bunch for the coupon! :)
  3. Replies
    177
    Views
    61,187

    LOL! you did make me look.

    LOL! you did make me look.
  4. Replies
    177
    Views
    61,187

    I think I have met all requirements for the...

    I think I have met all requirements for the contest
    1-Liked on facebook
    Subscribed to Everlast youtube channel
    2-Registered name on this forum
    3-Signature filled out
    4-Avatar pic posted...
  5. Replies
    2
    Views
    8,468

    OK, I finally got around to finishing this jig, I...

    OK, I finally got around to finishing this jig, I wont be able to use it for probably a year being I dont want to tear that far into my car yet. I machined up 2 pucks to replace the gear carrier...
  6. Replies
    16
    Views
    5,207

    Another good Idea!

    Another good Idea!
  7. Replies
    16
    Views
    5,207

    Wood doesnt contuct elec :(

    Wood doesnt contuct elec :(
  8. Replies
    16
    Views
    5,207

    Good idea! I'll try it.

    Good idea! I'll try it.
  9. Replies
    16
    Views
    5,207

    Everytime I try that they keep rolling on me,...

    Everytime I try that they keep rolling on me, especially when the gas preflows.
  10. Replies
    16
    Views
    5,207

    Yea, Im kinda thinking of laying it down inside a...

    Yea, Im kinda thinking of laying it down inside a 90 degree angle with a hole or gap in the center.
  11. Replies
    16
    Views
    5,207

    Holding fixture to join filler rods

    Anybody got any good ideas for a holding fixture to join short pieces of filler rod?
  12. Replies
    12
    Views
    5,636

    Hey, got an idea! You should open your own...

    Hey, got an idea! You should open your own Tanning Salon could charge people to hang out naked in your garage while welding! call it Weld-a-tan
  13. They dont look to bad to me, my first one looked...

    They dont look to bad to me, my first one looked like bird poop.
  14. Thread: Welding Tables

    by Buzz
    Replies
    84
    Views
    31,513

    Thats what I did, I made a frame under it with...

    Thats what I did, I made a frame under it with 1x1 square tube
    http://www.everlastgenerators.com/forums/showthread.php/2438-Project-2-Portable-welding-table
  15. Thread: Welding Tables

    by Buzz
    Replies
    84
    Views
    31,513

    My Table is 24"x48" x 1/4 inch thick, the plate...

    My Table is 24"x48" x 1/4 inch thick, the plate weighs 80lbs and cost me $40 thats 50 cents a pound, it was a drop piece the excess cut off a larger piece thus a big discount.
  16. Thread: Welding Tables

    by Buzz
    Replies
    84
    Views
    31,513

    I ended up making a table top table. 24x48 1/4...

    I ended up making a table top table. 24x48 1/4 thick, weighs about 100 lbs , portable that I can remove. nothing special but it works great. I need to make some kind of jig to square up material. if...
  17. Replies
    20
    Views
    7,033

    Yikes, we wont even go there. Powerblocks...

    Yikes, we wont even go there.


    Powerblocks are plates that fit inside each other and the weight is determined by installing a pin in select slots. similar to a weight stack on a universal gym....
  18. Replies
    20
    Views
    7,033

    You need another chicken!

    You need another chicken!
  19. Replies
    20
    Views
    7,033

    I use Dumbbells so much that I ended up...

    I use Dumbbells so much that I ended up investing in a set of PowerBlocks. I recommend them to anyone looking for adjustable Dumbbells.
  20. Replies
    20
    Views
    7,033

    That is correct, Dumbbell flat bench, Dumbbell...

    That is correct, Dumbbell flat bench, Dumbbell inclines, Dumbbell shoulder presses. The only thing Im missing is the ability to barbell bench press more weight. It used to be a big deal back in my...
  21. Replies
    17
    Views
    6,241

    That Mustang is beautiful, I would be driving it...

    That Mustang is beautiful, I would be driving it all the time, weather permitting, her 300c is a belly button car, everybody has one.
  22. Replies
    20
    Views
    7,033

    I use Dumbbells probably 75% of the time, the...

    I use Dumbbells probably 75% of the time, the ezcurl is only one exercise for Bi's I also do seated Dumbbell curls along with Dumbbells concentration curls, I never use a bar for any pressing...
  23. Replies
    20
    Views
    7,033

    All my weight plates are scratched, rusty and...

    All my weight plates are scratched, rusty and dirty, one of my bars is a 4 foot long 3/4 pipe and still has the threads on the ends. My house is over 100 years old,the basement is a dungeon.
  24. Replies
    20
    Views
    7,033

    I did go online and look for a used one but...

    I did go online and look for a used one but nuthin cheap or close, coulda got a new one with dumb bell handle for $20. It cost a tad over $2 to make and I had fun doing it. Red Necks? their...
  25. Replies
    17
    Views
    6,241

    Hey Bill if ya got em post some pics of the...

    Hey Bill if ya got em post some pics of the Mustang.
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4