Search:

Type: Posts; User: SeanMurphy265

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    522

    Old Power Plasma 60c Torch Question

    Is there a hand held plasma torch that would work with the older power plasma 60c?
  2. Thread: imig200

    by SeanMurphy265
    Replies
    4
    Views
    7,946

    I'm no electronic guru but, I do know the amp of...

    I'm no electronic guru but, I do know the amp of the breaker has something to do with the duty cycle of the Imig 200. When I used mine on a 30 amp breaker I could bump the duty cycle. I carried it...
  3. Replies
    14
    Views
    5,418

    13403 I'm guessing these are the points, I took...

    13403
    I'm guessing these are the points, I took some fine grit sand paper and cleaned them up. I have not had a chance to use the welder.
  4. Replies
    14
    Views
    5,418

    Yes it does have a buzzing sound. How do I check...

    Yes it does have a buzzing sound. How do I check the points?
  5. Replies
    14
    Views
    5,418

    I've been trying to use my 225lx with the 2t & 4t...

    I've been trying to use my 225lx with the 2t & 4t switch. I am having trouble getting the welder to fire off. It seems that I have to touch the metal before it will start welding. It is acting...
  6. Replies
    14
    Views
    5,418

    Thanks! I've been busy, I need to order me a...

    Thanks! I've been busy, I need to order me a pedal and make a cooler or sell the welder!
  7. Replies
    14
    Views
    5,418

    . I will look at it, but I'm thinking about...

    .

    I will look at it, but I'm thinking about getting a smaller pedal.
  8. Replies
    4
    Views
    6,449

    I ran a power arc 200 on a power horse 7000 from...

    I ran a power arc 200 on a power horse 7000 from Northern Tool for a solid two years without any issues. I ran it till I could afford an engine drive. When people ask me what I started with I tell...
  9. Replies
    14
    Views
    5,418

    I've been pretty busy at work and side jobs; so I...

    I've been pretty busy at work and side jobs; so I finally dug out my 225lx last week. The welder fires up just fine when I use the 2t and 4t switch. I'm guessing it's something to do with the foot...
  10. Replies
    14
    Views
    5,418

    I will check it when I get off work, thanks.

    I will check it when I get off work, thanks.
  11. Replies
    14
    Views
    5,418

    Thanks, where are the points located?

    Thanks, where are the points located?
  12. Replies
    14
    Views
    5,418

    225 lx issues

    I am having some issues with my 225lx and want to make sure I am not doing something wrong. I have used the welder just a few times in the 3 years I have owned it. I am having trouble getting it to ...
  13. Replies
    3
    Views
    4,473

    For that THC you will need to wire on the inside...

    For that THC you will need to wire on the inside of the machine. This is so it can read full voltage. I had the same issue, but I moved and never fixed it. You would do that if you had a...
  14. Replies
    8
    Views
    5,115

    It was shipping damage. It sat in the box for a...

    It was shipping damage. It sat in the box for a couple of weeks
  15. Replies
    8
    Views
    5,115

    I need need to sell this machine, it's an...

    I need need to sell this machine, it's an excellent welder I'll take $800.00.
  16. Replies
    38
    Views
    15,239

    Lots if times you can get the best deal off the...

    Lots if times you can get the best deal off the truck. I gave back two airgas lease bottles
  17. Replies
    8
    Views
    5,115

    Ok, I just assumed it would weigh less. I want...

    Ok, I just assumed it would weigh less. I want something that is easier to carry.
  18. Replies
    8
    Views
    5,115

    Everlast 250 MTS

    I've owned this welder for over a year and have welded with it 2-3 times. What little I have used it mig welding I do like it very much. I ordered a 200MTS from Amazon and was sent a 250MTS. I...
  19. Replies
    11
    Views
    4,357

    I believe this discussion has been tossed around...

    I believe this discussion has been tossed around a few times on the board. I agree with geezer; I used a NT Powerhorse 7000 for a good 2 plus years. I believe most new generators are going to be...
  20. Replies
    28
    Views
    14,636

    7018AC is a great option for inverter style...

    7018AC is a great option for inverter style welders in my opinion. 7014 is known as the sheet metal rod, and I personally find it to work very well on thin metals. I use 7018 (H4R) 1/8 Lincoln...
  21. Replies
    55
    Views
    17,505

    I have the harbor freight notcher and I have been...

    I have the harbor freight notcher and I have been happy with it. I do use good hole saws which I'm sure helps. I do plan to add some shims to mine.
  22. Replies
    37
    Views
    20,348

    Optimum conditions are the key! I will say that...

    Optimum conditions are the key! I will say that dry air makes a dramatic difference. I've owned a high frequency cutter with touch start that I felt had a good consumable life. A high frequency...
  23. Replies
    5
    Views
    4,655

    I already thought it was a very reliable welder! ...

    I already thought it was a very reliable welder! I'm not sure that I've even read any issues on the forums.:D
  24. Replies
    36
    Views
    10,750

    10476 Power Arc 140

    10476
    Power Arc 140
  25. One of the best investments I have made is a...

    One of the best investments I have made is a 100ft 10 gauge heavy duty extension cord. I have an air compressor that will trip its breaker with any cord thinner than 12 gauge. You would probably be...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4