Search:

Type: Posts; User: Odyknuck

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    6,070

    The small inline filters from HF are worthless...

    The small inline filters from HF are worthless for the CFM required for a Plazma cutter. You can drill out the end of the filter to increase the volume however then you reduce the dessicant's...
  2. Replies
    21
    Views
    9,495

    How about laying a desiccant pouch in the bottom...

    How about laying a desiccant pouch in the bottom of the compartment to absorb moisture?
  3. Replies
    18
    Views
    8,095

    Do you have the switch on the control panel set...

    Do you have the switch on the control panel set for TIG (HF)? If not your in tig lift mode and it works the way you describe.
  4. Replies
    106
    Views
    37,258

    That is just too funny!

    That is just too funny!
  5. Replies
    106
    Views
    37,258

    Thanks for the update Mark, that's good news.

    Thanks for the update Mark, that's good news.
  6. Replies
    106
    Views
    37,258

    Any chance my 50P is in that container?

    Any chance my 50P is in that container?
  7. What is your function switch set too, 2T or 4T. ...

    What is your function switch set too, 2T or 4T. Technically it should be set to 2T. Not sure what it does in 4T with the peddle.
  8. Replies
    15
    Views
    6,660

    For what little the switch costs I would replace...

    For what little the switch costs I would replace it. I would think that Everlast can supply you with a complete replacement switch assembly with cable and plug ready to go. Then you will not have...
  9. Replies
    3
    Views
    2,501

    Welcome aboard. I can not comment on the machine...

    Welcome aboard. I can not comment on the machine you purchased however based on what I have read here the IBGT technology is the way to go and is a major improvement over the MOSFET. I have a 250EX...
  10. The first thing I noticed about the Everlast...

    The first thing I noticed about the Everlast product line is the much higher duty cycle. For the hobbiest it's probably not an issue however for someone doing a lot of welding at one time it is...
  11. Replies
    36
    Views
    14,072

    What about the new all purpose Purple ones.

    What about the new all purpose Purple ones.
  12. Replies
    27
    Views
    12,954

    It does not take much water to cause issues with...

    It does not take much water to cause issues with the unit. Get rid of the water problem! Add a better filter. Do a search on here as there are a few good discussions on it.
  13. Replies
    18
    Views
    12,070

    Could it be a Polarity issue?

    Could it be a Polarity issue?
  14. Not to hijack the OPs thread however I have been...

    Not to hijack the OPs thread however I have been in the off road arena for over 25 years, racing, trail riding and building Buggys. Your bound to pick up a few tips and tricks along the way lol.
  15. Ok, Good to here as i do not want to see anyone...

    Ok, Good to here as i do not want to see anyone hurt. Can you at least make the "B" piller vertical? Are you going to "X" brace the "B" and/or "D" pillers?
  16. The Parallelagram cage design will collapse on...

    The Parallelagram cage design will collapse on the first rollover. I would recommend flipping the "B" and "C" pillers to angle towards the "A" piller so your cage is in compression.
  17. Replies
    2
    Views
    2,697

    Its a 2010 model, is it not covered under...

    Its a 2010 model, is it not covered under warranty?
  18. Replies
    19
    Views
    9,455

    I recently put a 1.5X in my cheapo HF hood. I...

    I recently put a 1.5X in my cheapo HF hood. I used a strip of duct take on each end to hold it in. Works fine.
  19. Replies
    3
    Views
    2,506

    What are you offering from CK?

    What are you offering from CK?
  20. Thread: 250EX oedered

    by Odyknuck
    Replies
    19
    Views
    6,146

    You could also use the static convertor to start...

    You could also use the static convertor to start a 5HP 3 phase motor. It will require a time delay off contactor to disable the static convertor after about 20 seconds. Thats what I did then VFDs...
  21. I do not know about the PP50 however my SC50 has...

    I do not know about the PP50 however my SC50 has a switch on the front panel that keeps the air on continuously or automatically when the trigger is pulled with a time out when released.
  22. Would an Anti spatter spray (PAM) help with the...

    Would an Anti spatter spray (PAM) help with the MIG dingleballs?
  23. Happy New Year Mark, Oleg, Alex and the rest of...

    Happy New Year Mark, Oleg, Alex and the rest of the staff.
  24. Replies
    15
    Views
    5,981

    Bed rails do come in handy don't they. LOL great...

    Bed rails do come in handy don't they. LOL great for light duty fabrication projects. The aluminum beads look pretty good for your first attempt. Of cource what do I know, as I have never done it. ...
  25. Replies
    43
    Views
    20,510

    Awsome welds!

    Awsome welds!
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4