Search:

Just upgraded from a 2014 PP50 on a CNC to a spanking new 82i- noticed 4 difference nozzle hole sizes. Anyone have some recommended uses for the various sizes?

We do some signs and say...

Yep/. spent the day w/ x207 Some email back and forth then we chatted. All over it! Thanks. Display board cometh... we'll try it..

OK. DC current meter in-house, and connected. Short run Video URL below. Essentially, notice the front display- On this 2013 model, I have never observed the front panel display anything other...

I certainly will. So we add to the mix here ... I went w/ this one from Klein. IT'll be here tomorrow. A few bucks more and a great YT review sold me. ...

Thanks Mark! Sent you a PM over at TractorbyNet too... appreciate the HF tip. The CM610A is equiv and does up to 600A AC or DC T-RMS clamp on (need to validate the clamp on part still). either way...

Hi all- For starters- This may not be a PP50 issue... It's all part of a CandCNC BladeRunner/Mach3 system.
ISSUE: Suddenly- the cut quality went south... The Torch Volts- took a dive too. Nothing...

I would hit the Everlast section of PlasmaSpider.com and/or some of the other forums that may apply to your Q's.

Gang... let me know if these are not priced appropriately?? I took a guess? I just hated to see the stock not being used. These can go OBO. HAppy Holidays everyone!

PP50 w/ CandCNC controls...

My Son and I recently designed and CNC machined a new floating head machine torch holder with custom built Trifimet S45 machine torch. This was done to repair our Precision Plasma table and to...

Uncle- I give up trying for pics. You Need to be signed up on that sight to see pics too. email me if ya want. I think I'll build a few anyway.... Practice. LOL.

I put up pics here.
http://www.hobby-machinist.com/attachments/s45print-jpg.116078/
http://www.hobby-machinist.com/attachments/photo4-jpg.116079/...

Not sure what the post did w/ the 4 pics I took? I cannot even open and it Will not let me edit now? email me for some actual photos if I do not get these up correctly. Sorry for the hassle. ...

Hi everyone, I bought a PP50 in 2013 and got the bug for CNC plasma really bad. The PP50 has run wonderfully and is a GREAT item.

But- I needed a machine torch! I finally took some time to...

What about a faraday cage? Put the PC under a metal/shielded setup of some type which is connected to its own ground outside? Also what type of PC Are you running? Since you can grab the...

Very neat. Thanks for sharing. In what part of china is this factory located?

Thanks Oleg. I did email Ray w/ my updates and issues. we spoke. I did built my own CNC cable to interface and it works fine. I sent Ray that info. My only issue now is cut data for materials. ...

Hi everyone,
Is there anyone who has sucessfully used the pin out on the rear of the 2013 Power Plasma 50. simply not much is out there. Trying to connect to a Bladerunner setup and I'm...

Can someone email me the newer PP50 manual in PDF or DOC form? I cannot locate mine, and if I recall it was the old/wrong one anyway. The website manual has zero reference to the CNC port on the...

could you point me to a link? the one I dloaded was really OLD. Not a current one.

Hi all; My manual is the one from the web. Seems old and the image of the rear is completly off? I did find the following image from one of the Forums for the CNC port on the PP50. Just wanted...

Is anyone here running a CandCNC Bladerunner setup w/ an Everlast PP50? I purchased the whole kit w/ Omic Sensor (called FeatherTouch) but It does appear you need to create or buy some type of...