Search:

Type: Posts; User: dawjr32223

Search: Search took 0.01 seconds.

  1. I'm going to try the mig wire straightening...

    I'm going to try the mig wire straightening trick, thanks for the tip!
  2. Replies
    11
    Views
    4,859

    Pictures of dust collector parts

    Hey, Guys - here are a few pictures of fabricated parts for the dust collector system and routing hood -

    All the best, Don917791789179918091819182
  3. Replies
    11
    Views
    4,859

    I'll get some pictures up when get it all online...

    I'll get some pictures up when get it all online - painting the initial branch of ductwork today. Welded it all together with my new 250EX, except for a few hit here and there with the mig. I simply...
  4. Replies
    11
    Views
    4,859

    Thanks again for the good words, guys....

    Thanks again for the good words, guys. Interesting technical talk about mufflers and resonators, just shows the depth of knowledge we've all come to embrace, make a living from, and share. I didn't...
  5. Check out Precision Plasma for their Patriot 4x8...

    Check out Precision Plasma for their Patriot 4x8 table. On the Hypertherm I'm using their Fine Cut tips. The control from CandCNC gives the user a lot of control over the cut. I'm still learning, but...
  6. Thanks for all the good words, guys. Hope all are...

    Thanks for all the good words, guys. Hope all are having a nice holiday.
  7. Replies
    11
    Views
    4,859

    Hey, Geezer. There is no piece (initially anyway)...

    Hey, Geezer. There is no piece (initially anyway) most of these types of mufflers are open flow-through just like a glass pack muffler for autos. Much of the sound pressure wave is diffused by being...
  8. Replies
    7
    Views
    11,572

    Hey, Guys - thanks for the good words. I'm...

    Hey, Guys - thanks for the good words. I'm keeping both of these systems separate because I've had the same concerns as you. The plasma table fans exit though the side wall of the building outside,...
  9. Yes, this plasma setup does make some pretty fine...

    Yes, this plasma setup does make some pretty fine pierces and cuts. Some bends would be tough to even get in a brake anyway without major setup time. It just makes me smile.

    Careful on that bike -...
  10. Good question. I think the bottom of this unit...

    Good question. I think the bottom of this unit will house a cooler. I've thought about making an "add-on" piece that would also house a plasma cutter or someone's mig. I did exactly that with my mig...
  11. Replies
    6
    Views
    3,990

    I make a fun series of people called "We're...

    I make a fun series of people called "We're nutz," - the last figure is part of a string of wall climbers, a female that's lost interest in climbing and reaching out for a butterfly. It's called...
  12. Replies
    7
    Views
    11,572

    Good question, Sean. You're right, this setup...

    Good question, Sean. You're right, this setup will not work at all for routing. I'm in the process of installing a proper dust collection system for the shop and table.
  13. Replies
    7
    Views
    11,572

    Plasma Table Ventilation

    Hey, Guys. Since I use my table for routing as well, I simply didn't want the hassle and mess of dealing with water. So I modified my water table to a downdraft table. Here's a couple of pictures. I...
  14. Replies
    6
    Views
    3,990

    Copper Butterflies

    I'd been making these butterflies by hand for the past couple of years, but here's a couple of pictures from the plasma cutter table.
  15. Replies
    11
    Views
    4,859

    Giant Muffler

    Hey,Guys. Needed a muffler for the new dust collector installation, but it had to be a certain length - so I made one. Here's some pictures.
  16. More Pictures

    More Pictures
  17. New Tig Cart Design - tell me what you think

    Hey, Guys. I just received my 250ex and needed a suitable home for it and not finding anything that I was willing to pay for that was unique or looked like it was from HF, I decided to design my own....
  18. Replies
    3
    Views
    2,349

    Hey, Guys and Merry Christmas! Finally got a...

    Hey, Guys and Merry Christmas! Finally got a minute to sit down and post a couple of pictures of the 2013 250EX, you'll probably find there's no outward difference in the look, but I've been told...
  19. Replies
    6
    Views
    9,760

    A little late on this thread, but I think you...

    A little late on this thread, but I think you would be fine - except for the heavy loading as you mentioned. Essentially it's simply support of the material and of no consequence if the torch passes...
  20. My, 2 cents. I just studied all the "turnkey"...

    My, 2 cents. I just studied all the "turnkey" systems out there that are sold to civilians and came to the conclusion that they're just silly on the pricing for what you get. I too wanted THC and it...
  21. Replies
    5
    Views
    2,339

    Thanks for the well wishes, Guys. Trip B, I'm...

    Thanks for the well wishes, Guys.

    Trip B, I'm in Mandarin, right across the river from ya. I worked in OP for fifteen years in the industrial loop at Commercial Casework, left them in 05. Back in...
  22. Replies
    3
    Views
    2,349

    Thanks for the well wishes! All the best, Don

    Thanks for the well wishes!

    All the best, Don
  23. Replies
    3
    Views
    2,349

    2013 250EX coming

    Hey, Guys - from looking around the forum a bit I see that there's interest in seeing what the new machine looks like since there's very little info available. I'll post some pictures when it gets...
  24. Replies
    5
    Views
    2,339

    TIG noob from NE Florida

    Hey, Guys - Another one looking to join the fun. Have a 2013 250EX coming - I'll post some pictures when it gets here. Been a self taught MIG guy for years and looking for the benefits that come from...
Results 1 to 24 of 24