Search:

Type: Posts; User: worntorn

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    686

    Thanks Sadly, that will be the last Al. project...

    Thanks
    Sadly, that will be the last Al. project for the PP256.

    Glen
  2. Replies
    12
    Views
    686

    All polished, mounted and decals...

    All polished, mounted and decals applied.14101141021410314104
  3. Replies
    12
    Views
    602

    A small local electronics store had a replacement...

    A small local electronics store had a replacement capacitor. The owner was able to read the label at that location on the board then look up the part. 484 nanofarads I recall
    I soldered the new...
  4. Replies
    12
    Views
    602

    No other problems, DC Tig, stick and Plasma work...

    No other problems, DC Tig, stick and Plasma work fine to full power.
    It would be nice to know the value for the capacitor. There are about 25 capacitors on the board with 3 different values. That...
  5. Replies
    12
    Views
    602

    I talked with Everlast extension 207 and...

    I talked with Everlast extension 207 and verified that the small board on the LH side is the AC board
    Couldn't see anything wrong at first then noticed this- looks like something has blasted off...
  6. Replies
    12
    Views
    686

    Forming the bottom 140911409214093140941409514096

    Forming the bottom
    140911409214093140941409514096
  7. Replies
    12
    Views
    602

    That sounds like a possible option. I could ship...

    That sounds like a possible option. I could ship the board to the Everlast techie(s) for testing and repair.
    Is this the AC board? Left side of machine from front.14090
  8. Replies
    12
    Views
    686

    Very custom, ready to race zero-turn! More...

    Very custom, ready to race zero-turn!

    More photos. Welded up, then many hours sanding and smoothing to flush weld. After that I spent a lot of time with the E wheel removing little curvature...
  9. Replies
    12
    Views
    686

    The red tank is on my Thruxton R. It holds 14.5...

    The red tank is on my Thruxton R. It holds 14.5 litres, not much more than a Commando Roadster tank (12litres).
    I wanted a bit more capacity so the buck was made with an extra inch of height vs the...
  10. Replies
    12
    Views
    686

    Using the English Wheel . I built this English...

    Using the English Wheel . I built this English Wheel in 2011 using the Power Ultra 205 in Tig mode. The tubing is very heavy wall , 5/16",which makes this English wheel very stiff and effective. As I...
  11. Replies
    12
    Views
    686

    Starting in to shape the sides and top1407614077

    Starting in to shape the sides and top1407614077
  12. Replies
    12
    Views
    686

    Motorcycle gas tank

    I recently built this tank for a Norton project bike. The plan is to use a Triumph Thruxton fairing at front, so the fuel tank top skin had to match a Thruxton R shape. The bottom has to be made to...
  13. Replies
    12
    Views
    602

    Mark, is there a separate AC board that can be...

    Mark, is there a separate AC board that can be replaced? If so, is this part still available?
    My thought is that if the board isn't crazy expensive I might purchase one and install it.
    Shipping the...
  14. Replies
    12
    Views
    602

    Thanks Christian, I'll try that. It looks...

    Thanks Christian, I'll try that. It looks surprisingly clean in there but you never know.
    Glen
  15. Replies
    12
    Views
    602

    PowerPro 256 kicks out on AC tig

    I purchased this unit in 2011. It's always worked perfectly for all functions. A couple of days ago while welding some 1/8" aluminum at 125 amps +-, the torch shut off.
    The overcurrent warning light...
  16. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    66986699670067016702

    66986699670067016702
  17. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    669566966697Next up was the gas tank. I made this...

    669566966697Next up was the gas tank. I made this from .063 3000 series Aluminum.
  18. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    Finished product after smoothing the welds, more...

    Finished product after smoothing the welds, more planishing in the ewheel and about half way thru the polishing process.

    I ran over the welds on the inside but only for fusion, no filler rod used....
  19. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    all three pieces made and welded together....

    all three pieces made and welded together. Material is just .050 thick 5052 aluminum, was a real challenge for me to weld. But I have a great machine (PP256) for that so it turned out fine.
    ...
  20. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    After some hammering and some planishing on the...

    After some hammering and some planishing on the ewheel I had two of the three pieces needed for the cowl roughed out-

    http://i1233.photobucket.com/albums/ff397/worntorn1/003-4.jpg
  21. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    So I started back in on this project about mid...

    So I started back in on this project about mid winter. First off I made up a pattern or a "buck" for the rear cowl and seat pan.

    I wanted the tank/seat and cowl lines to flow together like one...
  22. Thread: Egli/Vincent

    by worntorn
    Replies
    77
    Views
    30,328

    finished at last

    Got it all done and have been out riding it the last couple of weeks. It goes like hell, weight is only 350 lbs.
    Will post some pics in the next day or two.

    Glen
  23. Replies
    12
    Views
    4,928

    Also, does anyone have info on the amp...

    Also, does anyone have info on the amp adjustment mentioned by Mark?

    Glen
  24. Replies
    12
    Views
    4,928

    looks like I'll have to buy an ex 250 if I want...

    looks like I'll have to buy an ex 250 if I want to weld pop cans!

    Seriously, 24 amps is actually low enough for any practical welding I will ever need to do



    I'm away from home for a few...
  25. Replies
    12
    Views
    4,928

    Hi Mark For the low setting, no I haven't...

    Hi Mark

    For the low setting, no I haven't tried it in dc mode, just ac. I have the start amp knob turned down as far as it will go. I've tried it with both the foot pedal and the switch,
    2T and...
Results 1 to 25 of 313
Page 1 of 13 1 2 3 4