Search:

I am gonna have to keep an eye out on the new models.. I went from an analog to a digital and would not even think twice about going back..

Wow I havnt been on in awhile but I love my origional 255EXT.. I would love to have had it dual phase like the new ones. I didn't think it could get any better..

As to the reverse direction, I...

I have had 2 air cooled flex heads basically melt the thin rubber around the end of the torch at less than max amps.. I have since been using a water cooled wp20 and cant imagine going back.. Now I...

You could always use a sub domain for this purpose as well. When the company i work for was making a new site, we had a subdomain they used the entire design process and then I just flipped the...

I could probably lend a hand with fixes if you guys need as well.

All new Pistons/Rods
http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3332.JPG

And back on task.. First one shoved in..
http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3333.JPG
...

http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3309.JPG


And the new Block... Painted in POR15
http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3314.JPG

Ran a hone through...

And the fun begins, but plans have changed to building this over winter and getting a different car running before the first snow fall..

First 2 ecu's :)...

Any updates to who the winners are now that the new units have gone out?

Thats pretty cool. I have wanted to build a little engine that for a long time now..

On another note, I need to update this thread.

I was under the imression that it had a plug for the cooler but when I unboxed mine, I also noticed that it did not have one. I also was very impressed with the handling from UPS other than they left...

Why not call oleg and ask him about your shipment?

The timing of this couldn't be more perfect. Earlier would have helped but it is still going to arrive just in time for my needs. :)

start at 501, now at 604 posts.

watched/liked/commented on the following.

https://www.youtube.com/watch?v=KN-aYQWW7a4&list=LLU-9jSP0SUFCYCLNA79zzMQ&index=1...

As I mentioned there has been progress but lack of updates. Here I will catch it up..

This is how I run between the MS and the factory ECU...

yea I grew up in California and remember the smog laws. Here in Iowa there is no smog checks at all, just go down to DOT (same as DMV for the most part) and get your plates. When I lived in Arizonia,...

I havn't been on in a few days but I have more parts here now however I have not taken any picture. The list of parts is complete gaskets sets, new Big Valves, New Valve seats, new Valve seals, AN...

Different sensor and probably different version MS board to. Also if they put a shim in his sensor, that might change things I bet. Anything that can interfer with the signal is bad. My signal and...

Idle is dead perfect on the factory ECU. My idle valve is set to PWM Warmup only so it opens the tb 0% at 160 deg F or higher. I just need to work through it still.

In regards to the crank sensor,...

My Innovate was reading .6 lower than the MS but it is correct to follow the Innovate Guage.. Imoved the ground for the Innovate to the same location as the MS tonight and now it is only .1-.2 lower...

Looking forward to getting mine :)

Sounds like there is a plan to fix the small issues to.

First off, I will answer the lamda question. The Innovate wide band was put in place of my factory sensor. When running the wideband, it has a harness that actually goes to a plug on the guage. The...

The tooth logger definetly helped diagnose my problem with it. If his was already working, might wanna make sure the sensor is not going out. They like to stop reading when they get warm when they...

Plugged in the MS3 for a temp time to try it out. Found it didn't work right off the bat..
http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3245.JPG

When I started this, I made a...

So more parts are here.
http://www.projekt6.com/jackal/GalleryRoot/12VBuild/100_3253.JPG

Started putting the standalone in the car. Cut a hole in the rain tray area to run the harness through....