Powermaster 226 has HF but will not arc

I was welding last night(aluminum) and stopped to reposition my work(thin work with little amps). Went to start back welding and only has HF start. I even tried striking the arc directly to the ground glamp but no luck. Tried a diff foot pedal and the factory hand trigger setup. Few notes, reads around -032 amps and the display will not change no matter what knob I turn. When I try to strike the arc it basicly flashes to 000 on the display.
This couldnt have happened at a worst time, have a customer flying in this saturday and I have just a little welding left to finish for him
.

Any ideas?? Anyone at everlast feel free to call me at 434-470-2700 if needed or you have some ideas please

Won't work with the torch switch? Does same thing? Can you scratch start it?

Quote:

---

Originally Posted by performance

Won't work with the torch switch? Does same thing? Can you scratch start it?

---

No. Same thing with the torch. And will not scratch start either. All I can get is the HF

Sounds terminal. Have you tried the other processes? Anything? Only other thing to do is remove the cover and see if there is anything obvious that is loose, or broken. If nothing, call tech support at ext 207.

Quote:

---

Originally Posted by performance

Sounds terminal. Have you tried the other processes? Anything? Only other thing to do is remove the cover and see if there is anything obvious that is loose, or broken. If nothing, call tech support at ext 207.

---

Ill try stick tonight(TIG is the ONLY function I have used on this machine). If same thing I will look for obvious after removing the cover. if I dont see anything obvious, and I send it in its still under warranty(by just a hair LOL)how does the warranty work? What all does it cover? Any chance I can just upgrade while you have the unit?

Quote:

---

Originally Posted by singlesupra

Ill try stick tonight(TIG is the ONLY function I have used on this machine). If same thing I will look for obvious after removing the cover. if I dont see anything obvious, and I send it in its still under warranty(by just a hair LOL)how does the warranty work? What all does it cover? Any chance I can just upgrade while you have the unit?

---

Any info on how the warranty works?

For full details, There are directions and information on our site under the warranty section(terms and conditions). But, you have to call tech support to get an rma, fill out the form with the details AND RMA number then you have to ship it back if its something that can only be repaired at the repair center. The warranty covers repairs, and labor. You cover the shipping.

No upgrade on that old of an unit.

Well Damn...pulled the cover didn't see anything obvious other than a slight loose connection and out cover back on. Pushed it into place and put cover back on. Started welding correctly right after. Just tonight I have the same issue again... can I still use the same return number? My warranty runs our in a few days and wish now i had just sent it back vs takin the cover off. Hope likening to u guys to take the cover off myself didn't screw me outa warranty work

Let me know if I can use the same return number please

Quote:

---

Originally Posted by singlesupra

Well Damn...pulled the cover didn't see anything obvious other than a slight loose connection and out cover back on. Pushed it into place and put cover back on. Started welding correctly right after. Just tonight I have the same issue again... can I still use the same return number? My warranty runs our in a few days and wish now i had just sent it back vs takin the cover off. Hope likening to u guys to take the cover off myself didn't screw me outa warranty work

Let me know if I can use the same return number please

---

ttt?? anyone?? I hate to have to pay for the warranty thats out a day or two. Please let me know

Quote:

---

Originally Posted by singlesupra

ttt?? anyone?? I hate to have to pay for the warranty thats out a day or two. Please let me know

---

Your best bet is to call support to verify that you can use the same RMA#.

You can use it, just send it in. But before you send it in make sure it isn't in lift arc or the the main wire running to the HF board hasn't pulled loose.

Quote:

---

Originally Posted by performance

You can use it, just send it in. But before you send it in make sure it isn't in lift arc or the the main wire running to the HF board hasn't pulled loose.

---

I pulled the cover again last night, which is the HF board exactly? And thanks for being so easy to work with, its why I have sent many many people you guys way over the years

Quote:

---

Originally Posted by singlesupra

I pulled the cover again last night, which is the HF board exactly? And thanks for being so easy to work with, its why I have sent many many people you guys way over the years

---

It should be the board with the points on it. Probably not a bad idea to have a look at all the plugs, while you have the cover off. If it got bounced hard enough to knock one loose, there could be others that are barely hanging on.

Quote:

---

Originally Posted by Rambozo

It should be the board with the points on it. Probably not a bad idea to have a look at all the plugs, while you have the cover off. If it got bounced hard enough to knock one loose, there could be others that are barely hanging on.

---

To be honest the Welder has sit in the same place for the past 4+ yrs so nothing has ever been bumped at all since its been here.

Quote:

---

Originally Posted by singlesupra

To be honest the Welder has sit in the same place for the past 4+ yrs so nothing has ever been bumped at all since its been here.

---

Sometimes repeated heating and cooling cycles can eventually work a connection or joint off that might have been loose to begin with.

At this point I don't see anything obvious and am going to just send it back in. I don't want the warranty to be months out before they get it back.
thanks for the replys and ill update what the issue was(if they tell me)

FIgured Id update this. After using the everlast Id guess 20 times over the course of the years and all the issues I had, I sold it on craigslist for around $50 bucks. When I first purchased it, for about 3 months it was a royal pain to weld with so I had to buy a upgraded pedal. Used it as I said a few more times and had this issue. Sold it in 2013, got a lincoln 175 square wave used for cheaper than this new one cost me and it hasnt skipped a beat. I have used it weekly, sometimes daily for weeks at a time without so much as a hickup.
What I learned.... These are throw away welders. You are much better off purhcasing a good used welder vs one of these. I love a deal as much as anyone and sure when it welds, it welds great but they just are not made to last. Its like purchasing anything else, you get what you pay for. Id say maybe buy one if you only use it once in a while but thats what I did and it still didnt last.
No hard feelings on my end, and hope none on everlast end with my review. I tried to cheap out and in the end after buying this and my lincoln, I could have purchased a higher amp real welder. Hope most dont have the luck I had with it. Toys have there time and place but NOT in my shop, I have to have reliabilty

That is a welder that has been out of production for about 7 years now. Welders aren't even close to being the same or built the same. They are made to last. There are a lot of terrible reviews of the Lincoln SW 175 and issues they had with the board. More than one person was told basically, that the 175's were throw away because of the cost of the boards and the problems. Everyone is going to have a different opinion and experience...but I am not sure what was wrong with your Everlast. You still did not say and over 3 years later, you post this up. I hate you had that experience. But it is a fairly isolated opinion. All of these IGBT models are still being supported and are fixable. Units still carry a 5 year warranty. If they were not good, we could not extend a 5 year warranty on them. As far as resale, you probably hurt yourself. I've seen Everlast stuff go for almost retail on craigslist and ebay. I've seen a few go for more than what the customer paid us for it.

I wont argue about the lincoln 175, Ill just say this is the first Ive heard anyone consider it a throw away. Look, if I touched a nerve, sorry it wasnt my intention. I basicly got about 3 hours worth of welding out of mine due to issues at first, then the pedal and then the last HF start issue. I couldnt give you a final resolution as to what was wrong since I knew I was about to ramp up my fabrication and needed something that worked every day. I purchased the used lincoln 175 and about 6 months ago purchased another. The lincoln 175 actually has one of the best names and reputations out there and most only complaint is the 175 amps.
As for getting less than it was worth, not sure of your area but chinese welders here dont sell well and they definately dont sell well when they are a 40#, dead in the water paper weight.

As I said earlier my purpose for updating this thread was to give everyone my final thoughts on the welder. Im sure someone out there has had back luck with a lincoln 175 and Id welcome there review also. I did read about a potential board issue but it seems those are fixed for about $175 so I dont know who would throw away a $2000 welder for such a cheap fix but thats on them, not me. You can only cut prices on things so much until they become cheap, and thats exactly how everlast can sell these things this "cheap". I say cheap on initial purchase but the first time it fails to operate it costs you much more as well as having to buy a welder that will work daily. Sure these things have there time and place, but a shop like mine that cant take the weeks it takes to send away and get back it has no place.

So again, goodluck to all who purchase

Quote:

---

Originally Posted by singlesupra

chinese welders here dont sell well

So again, goodluck to all who purchase

---

I hope you realize that your 175 is not made in the USA.

I dont care if its made on pluto, as soon as you open the everlast box and feel the components its apparent its a cheaply made product. Debate that all you like but when you are constantly having to say "check the cog for slippage" on a new part or "check this and that" its an inferior product

Quote:

---

Originally Posted by singlesupra

I wont argue about the lincoln 175, Ill just say this is the first Ive heard anyone consider it a throw away. Look, if I touched a nerve, sorry it wasnt my intention. I basicly got about 3 hours worth of welding out of mine due to issues at first, then the pedal and then the last HF start issue. I couldnt give you a final resolution as to what was wrong since I knew I was about to ramp up my fabrication and needed something that worked every day. I purchased the used lincoln 175 and about 6 months ago purchased another. The lincoln 175 actually has one of the best names and reputations out there and most only complaint is the 175 amps.
As for getting less than it was worth, not sure of your area but chinese welders here dont sell well and they definately dont sell well when they are a 40#, dead in the water paper weight.

As I said earlier my purpose for updating this thread was to give everyone my final thoughts on the welder. Im sure someone out there has had back luck with a lincoln 175 and Id welcome there review also. I did read about a potential board issue but it seems those are fixed for about $175 so I dont know who would throw away a $2000 welder for such a cheap fix but thats on them, not me. You can only cut prices on things so much until they become cheap, and thats exactly how everlast can sell these things this "cheap". I say cheap on initial purchase but the first time it fails to operate it costs you much more as well as having to buy a welder that will work daily. Sure these things have there time and place, but a shop like mine that cant take the weeks it takes to send away and get back it has no place.

So again, goodluck to all who purchase

---

Well here you go: https://www.google.com/search?q=squa...utf-8&oe=utf-8
No, no nerve touched here. But don't expect a pass when you've made some inaccurate statements.
But seriously, let's be honest, YOU threw it away. They aren't throw away welders! The older Everlast welders are repairable and fixable, much more so than other machines in it's class in general. The boards are repairable as well. You are making a statement that is easily something that can be seen through. We use NAME brand components and the part numbers are usually right on the welder. We offer upgrades to the existing pedals and have for some time, with SSC controls. We also have improved our pedals and haven't had that pedal in seveal years, but most if they had an issue were fixable, and there were threads here on how to do so.

Also you are making a statement about an early unit that is no longer made. But we still fix them if they tear up. We have updated the foot pedal issue. You are making a current and dismissive assessment of the product line based on an Old, early design, and one that we are still supporting and repairing. You had an issue early on, but didn't really make the effort to resolve it. You dumped the unit and then bought something that isn't even in the same class and capability of the machine. You compare apples to oranges. But hey, who'd throw away a 1300 dollar welder over such a cheap and easy fix? Right? Boards for that machine are cheaper than what you quoted on yours...

But thanks for an opinion and closure on this thread 3 years after you started it. I just wish it had been more about your experience with the machine and less about a summation of the current Everlast product line (and really the line since 2010) as a whole.

Quote:

---

Originally Posted by performance

Well here you go: https://www.google.com/search?q=squa...utf-8&oe=utf-8
No, no nerve touched here. But don't expect a pass when you've made some inaccurate statements.

Yes, a nerve was struck on your end, not mine. Nothing innacurate about everlast being a hobby welder at best. As for your link, anything new used beat on or old as dirt will have a few bad apples, perhaps you should, being a everlast pusher know this more than anyone... Your very forum with all the "my welder wont do this or that" should show you where reliability stands with these things. Go to a real welder site and you will see a few posts about issues but nothing like these things...
But seriously, let's be honest, YOU threw it away. They aren't throw away welders! The older Everlast welders are repairable and fixable, much more so than other machines in it's class in general. The boards are repairable as well. You are making a statement that is easily something that can be seen through. We use NAME brand components and the part numbers are usually right on the welder. We offer upgrades to the existing pedals and have for some time, with SSC controls. We also have improved our pedals and haven't had that pedal in seveal years, but most if they had an issue were fixable, and there were threads here on how to do so.

I threw it away simply because I couldnt deal with the constant downtime from the welder. I had a decision to make, fix the board and I still have to update the torch, pedal, etc.. or buy something tried and true. The instant you open the box and see the "manual" its clear as day exactly what you have purchased....

Also you are making a statement about an early unit that is no longer made. But we still fix them if they tear up. We have updated the foot pedal issue. You are making a current and dismissive assessment of the product line based on an Old, early design, and one that we are still supporting and repairing. You had an issue early on, but didn't really make the effort to resolve it. You dumped the unit and then bought something that isn't even in the same class and capability of the machine. You compare apples to oranges. But hey, who'd throw away a 1300 dollar welder over such a cheap and easy fix? Right? Boards for that machine are cheaper than what you quoted on yours...

correction, i had several issues fixed before the final straw that broke the camels back
I dont care if its not made anymore, when I purchased it STRAIT FROM EVERLAST if it was an older unit that is no longer made I sure wasnt told. And, yes, the first FEW issues I had early on I went through all the hoops that are typical of chinese welders. "try this", "tighten that" and I got it to be a 100% good welder, 90% of the time. What ended up "fixing" the first few issues was I had to purchase a upgraded pedal because the one it was shipped with was, yet again, an older design that half ### worked. Honestly I could have sent it back, had it fixed and sold it but I didnt want my name associated with the thing when it #### the bed AGAIN
But thanks for an opinion and closure on this thread 3 years after you started it. I just wish it had been more about your experience with the machine and less about a summation of the current Everlast product line (and really the line since 2010) as a whole.

---

It was about my experience about the damn welder, what are we talking about? Someone elses welder? You go to ANY website you guys are on and you blame shift everything. The "manuals" are terrible, you blame it on the printer. The pedals stop working, you tell the customer to check the cog, etc.. Accept responsibility, you sell inferior products compared to lincoln/miller. At everlasts price point it should be inferior, embrace that. Thats YOUR market. Dont try to pass the green machines off as something its not. Ive given my review, you dont like it, sorry. The green machine drones here may be biased enough to see that you have not once taken responsibility over this outcome but anyone looking to purchase and spend there hard earned dollars will surely see who is right and who is wrong. Goodluck with the business

Nonsense,

Most forum members here and elsewhere have seen the good character, reasonableness, and effort of Everlast staff toward their customers and welding units. I mean, I certainly have.

The manuals are not "terrible". They're quit good, not flawless. I mean, what are you expecting, pop-out diorama scenes.

The quality, superior value, superior warrantee, and their support has earned Everlast the undoubted top spot for imported units on the North American continent. And this very forum is an example of an added benefit of Everlast service.

Of course, the Lincoln SW 175 is a proverbial yacht anchor; it's under-powered and over-priced, especially since it has almost no features at all. I mean, it's priced around what my 210EXT is, except without: AC Frequency Control, AC Balance, Digital Interface, Wave Forms, Memory Settings, Compactness, etc. And that's why the SW 175 is not being produced anymore, because it can't compete with Everlast units like my own 210EXT, which out-classes the SW 175 in every way.

Yeah, the great majority of us Everlast customers, that you're apparently calling "drones", are happily spending our money on great Everlast units, and keeping more of our money in our pockets while enjoying units and feature-sets that would otherwise cost two or three times as much. So, we're happy, what's your problem?

Anyway, it seems like you're needlessly blaming Everlast for "my experience", which is your emotions or so-called "feelings", of which only you control, or fail to. And, again, Everlast has many examples that I've seen of this forum where it has seemingly gone above and beyond for many of its customers. That's just an objective fact of reality that both yours and my own subjective "experience" cannot rightly refute.

Quote:

---

Originally Posted by singlesupra

It was about my experience about the damn welder, what are we talking about? Someone elses welder? You go to ANY website you guys are on and you blame shift everything. The "manuals" are terrible, you blame it on the printer. The pedals stop working, you tell the customer to check the cog, etc.. Accept responsibility, you sell inferior products compared to lincoln/miller. At everlasts price point it should be inferior, embrace that. Thats YOUR market. Dont try to pass the green machines off as something its not. Ive given my review, you dont like it, sorry. The green machine drones here may be biased enough to see that you have not once taken responsibility over this outcome but anyone looking to purchase and spend there hard earned dollars will surely see who is right and who is wrong. Goodluck with the business

---

Quote:

---

Originally Posted by singlesupra

It was about my experience about the damn welder, what are we talking about? Someone elses welder? You go to ANY website you guys are on and you blame shift everything. The "manuals" are terrible, you blame it on the printer. The pedals stop working, you tell the customer to check the cog, etc.. Accept responsibility, you sell inferior products compared to lincoln/miller. At everlasts price point it should be inferior, embrace that. Thats YOUR market. Dont try to pass the green machines off as something its not. Ive given my review, you dont like it, sorry. The green machine drones here may be biased enough to see that you have not once taken responsibility over this outcome but anyone looking to purchase and spend there hard earned dollars will surely see who is right and who is wrong. Goodluck with the business

---

Obviously it is NOT soley about your experience with the welder as you are categorically making comments about the company and ALL the products in general...even in your rebuttal. C'mon. I am not blame shifting, but putting it squarely where it needs to be. You gave up after 3 hours you said. You didn't follow though and you are making categorical comments based on a 7 year old product that did have a limited run. The manuals? Have you even read them? They are online and they are for everyone to see. We don't blame printers.

Quote:

---

Originally Posted by christian

Nonsense,

Most forum members here and elsewhere have seen the good character, reasonableness, and effort of Everlast staff toward their customers and welding units. I mean, I certainly have.

The manuals are not "terrible". They're quit good, not flawless. I mean, what are you expecting, pop-out diorama scenes.

The quality, superior value, superior warrantee, and their support has earned Everlast the undoubted top spot for imported units on the North American continent. And this very forum is an example of an added benefit of Everlast service.

Of course, the Lincoln SW 175 is a proverbial yacht anchor; it's under-powered and over-priced, especially since it has almost no features at all. I mean, it's priced around what my 210EXT is, except without: AC Frequency Control, AC Balance, Digital Interface, Wave Forms, Memory Settings, Compactness, etc. And that's why the SW 175 is not being produced anymore, because it can't compete with Everlast units like my own 210EXT, which out-classes the SW 175 in every way.

Yeah, the great majority of us Everlast customers, that you're apparently calling "drones", are happily spending our money on great Everlast units, and keeping more of our money in our pockets while enjoying units and feature-sets that would otherwise cost two or three times as much. So, we're happy, what's your problem?

Anyway, it seems like you're needlessly blaming Everlast for "my experience", which is your emotions or so-called "feelings", of which only you control, or fail to. And, again, Everlast has many examples that I've seen of this forum where it has seemingly gone above and beyond for many of its customers. That's just an objective fact of reality that both yours and my own subjective "experience" cannot rightly refute.

---

And the fact is Ill be passing my lincoln down to my kids while you cant even remember your green machine

Quote:

---

Originally Posted by singlesupra

And the fact is Ill be passing my lincoln down to my kids while you cant even remember your green machine

---

You sound childish and make foolish assumptions.

Quote:

---

Originally Posted by performance

Obviously it is NOT soley about your experience with the welder as you are categorically making comments about the company and ALL the products in general...even in your rebuttal. C'mon. I am not blame shifting, but putting it squarely where it needs to be. You gave up after 3 hours you said. You didn't follow though and you are making categorical comments based on a 7 year old product that did have a limited run. The manuals? Have you even read them? They are online and they are for everyone to see. We don't blame printers.

---

3 hours? No, try 3 years(as my posts have clearly said) of dealing with almost always something being wrong with it. So what you are saying is I happen to purchased a bad run? Look bud, you can try all you want but theres a reason you see 500 blue or red machines on a job site to every green one you see. Thats my point, its a hobby welder, at best, but in your defense its priced accordingly

So again, as I said, good luck with the company and I hope people who are on the fence of buying a quality welder realize that by the time you replace all the junk accys that come with everlast that they are not far or even on price on a machine that will still be welding for there kids. Even you yourself keep bringing up the fact that it was a "7 year old welder", exactly my point, these things are not made for the long haul. It wasnt 7 years old when I purchased it and was advertised buy you guys as top of the line at the time.

I have no stake in your company I just hope people see my real world review, not like 99% of the other everlast reviews, but an actual review after several years. Im sure a few, and I mean a very few, may last but thats the difference between everlast/any of the "import" machines, they are throw away welders that if you get 2 or 3 years out of them with no issues count yourself lucky

Again, you are not even making fair comparisons or reasonable assertions. 1) The accessories you received have been change a LONG time ago. 2) Your unit was an early transition model away from MOSFET to IGBT technology in 2009. 3) With other name brands you have to buy the accessories, which again adds to your purchase cost, which again offsets the difference 4) We offer upgrades to our accessory packages as well in the likes of SSC and CK worldwide. 4) We have a lot of those old units, and even our old mosfets dating back to 2004 still in service. We still stock parts and consumables for them, and if we don't have them, we still can get them and repair them if we are out. 5) We have huge name companies in everything from racing to the aerospace industry using our products daily. You are far behind the progress we made in the past 7 years. I have put whole fleets of our products in Union hall training centers. I have put multiple units in many welding schools, many well known all across this country. We have international distributors on every continent except Antarctica. 6) We are have had 7 years of consecutive growth, in the double digits. 7) We've invested major money in our factories, production, QC and testing over the last few years. 8) We have monthly productions inspections (in person) and regular, un-announced separate independent inspections of the production facilities.

You said you only used it for 3 hours before you had issues and then you indicated you gave up after that. Previously you said you had only used it about 20 times. Really doesn't sound right to me, as in there is something not adding up.
As far as passing that unit on, the 175 has been problematic, and numerous changes have been made. I have LIncoln stuff too. One control board on a well sold Ranger 8, which are designed to last for years was out of production, only 8 years after it was made. It was problematic and they had made new ones, but the old ones weren't the same or interchangeable. They said it would take 6-8 weeks to get a new one produced and they'd have to schedule a production run to do it after I ordered it...and it was going to be over 400.0 for a simple control board without much on it. I had to have it repaired at a third party facility and it still cost nearly 200.00 for it. Think again. Lincoln is selling stuff made in China now, that is assembled in Mexico, and they are having all sorts of issues with their stuff...stuff we've never even had an issue with on our products. And people are steamed...as they were out of replacement units and parts for several months. I am you will pass the 175 on, and am sure your children will enjoy you passing on an outdated and orphaned boat anchor to them.

Quote:

---

Originally Posted by performance

You said you only used it for 3 hours before you had issues and then you indicated you gave up after that. Previously you said you had only used it about 20 times. Really doesn't sound right to me, as in there is something not adding up.
As far as passing that unit on, the 175 has been problematic, and numerous changes have been made. I have LIncoln stuff too. One control board on a well sold Ranger 8, which are designed to last for years was out of production, only 8 years after it was made. It was problematic and they had made new ones, but the old ones weren't the same or interchangeable. They said it would take 6-8 weeks to get a new one produced and they'd have to schedule a production run to do it after I ordered it...and it was going to be over 400.0 for a simple control board without much on it. I had to have it repaired at a third party facility and it still cost nearly 200.00 for it. Think again. Lincoln is selling stuff made in China now, that is assembled in Mexico, and they are having all sorts of issues with their stuff...stuff we've never even had an issue with on our products. And people are steamed...as they were out of replacement units and parts for several months. I am you will pass the 175 on, and am sure your children will enjoy you passing on an outdated and orphaned boat anchor to them.

---

Not quite sure where you are getting your information, Ive clearly said time and time and time again I bought the damn thing, it came half ### working. After weeks/months of dealing with the "check this, check that" of everlast support it was determined the pedal was the root cause of most of the issues. Fast forward 2 years or so, after using it for maybe 20 times, the unit would not do anything other than the HF arc. Not sure why this is so hard to grasp. But then again, after doing a quick search it seems many many many others have had the same issue. Need links?
Dont try to twist my words, you are already coming across as an ### already and Im sure once this thread is searched more and more people see how arrogant you have been you will lose even more customers. So again, good luck with the company. This will be my last response to you. If people find there way to this thread and think you have handled yourself professionally and want to purchase the throw away welders, it doesnt effect me either way. If they see what they already knew and it costs you sales, thats fine with me also.
Now, if you have anything else to say to me feel free to PM me and we can meet for a beer, I travel quite a lot and have no issue finishing this face to face. I am honestly shocked you have the time to respond with as many products you have that have issues. Just click the back button and scroll down the forum for proof.

And btw, my boat anchor still outwelded the everlast in every metal I ever used it on. I had several career welders who tried using the everlast with about as good of luck as I had with it. Oh, but I forgot, that was a ragged unit that wasnt in production long. In a couple years, the ones you are rebadging now(or painting green, however you want to spell it) will be blamed on something else as well.

To anyone else who happens to google search there way here, dont take my word for it. Google long and hard, find reviews after a few years. Sure, SOME of the everlast come out of the box working but thats not a real review.

Last post I promise, as for the crap accys, I still have the "regulator" that came with the unit. In one of the times it was actually working(or maybe it was one of the times I was fooling with the stupid thing trying to troubleshoot it) I hear a loud POP, look over and the regulator blew itself apart LOL. BUT this is everlast and Im sure it was because it was one of the "old units and are now not shipped with the cheapest regulator money can buy from a Chinese sweatshop".

Quote:

---

Originally Posted by zoama

You sound childish and make foolish assumptions.

---

I'm sure we all know every forum attracts those that need to make sure the rest of the world is aware that "they" are the biggest @sshole in the world.

This is too funny. (A plant for sure)

You joined our forum in Aug 2009, then sold your welder in 2013 (that is a long time for 20 uses or 3 hours; whichever)?

Now it's 2016, years later and you come here to post about a welder you bought 7 years ago? Our units have improved for sure in that time. But if you had a problem in 2009, or 2013, I would think you would be over it by now and moved on. Sheesh.

I too have owned Lincoln and Miller as well. Our units weld just the same. If you see weldingtipsandtricks.com video, he uses our units quite often as well. Longest case of sour grapes I have ever seen. Also, I still have a couple of the old regulators in service with no problems.

Quote:

---

Originally Posted by everlastsupport

This is too funny. (A plant for sure)

You joined our forum in Aug 2009, then sold your welder in 2013 (that is a long time for 20 uses or 3 hours; whichever)?

Now it's 2016, years later and you come here to post about a welder you bought 7 years ago? Our units have improved for sure in that time. But if you had a problem in 2009, or 2013, I would think you would be over it by now and moved on. Sheesh.

I too have owned Lincoln and Miller as well. Our units weld just the same. If you see weldingtipsandtricks.com video, he uses our units quite often as well. Longest case of sour grapes I have ever seen. Also, I still have a couple of the old regulators in service with no problems.

---

Did you really just accuse me of being a plant? After I purhcased the welder directly from you? Actually I ran across this post after another person asked me about how it was holding up so it reminded me to update the thread. Your products are junk, your attitude here is on par. I had nothing but issues with the thing from day one, with proof. Keep up the snide remarks, it just proves what kind of company you guys run and everytime someone searches this they will see. Honestly Im suprised you havnt deleted this thread like the ones you did on several other forums....

Quote:

---

Originally Posted by singlesupra

Did you really just accuse me of being a plant? After I purchased the welder directly from you? Actually I ran across this post after another person asked me about how it was holding up so it reminded me to update the thread. Your products are junk, your attitude here is on par. I had nothing but issues with the thing from day one, with proof. Keep up the snide remarks, it just proves what kind of company you guys run and everytime someone searches this they will see. Honestly I'm surprised you haven't deleted this thread like the ones you did on several other forums....

---

Maybe they want others to see you make a fool of yourself. For every whinny child like you, there are thousands of happy adult customers welding with Everlast.
I've owned Everlast machines for at least 6 years now. I've had one minor problem that I repaired myself. All my machines work perfectly.

Quote:

---

Originally Posted by singlesupra

Did you really just accuse me of being a plant? After I purhcased the welder directly from you? Actually I ran across this post after another person asked me about how it was holding up so it reminded me to update the thread. Your products are junk, your attitude here is on par. I had nothing but issues with the thing from day one, with proof. Keep up the snide remarks, it just proves what kind of company you guys run and everytime someone searches this they will see. Honestly Im suprised you havnt deleted this thread like the ones you did on several other forums....

---

I'm not being rude, also I have not disabled any thread on "our forums or any". Your odd timeline just seems fishy to me, that's all (like you had an adgend of some kind).. Probably others might think that as well. Just the facts, nothing rude. You are the one that came back to insult us.

I, like Mark, have used everlast since working there (lincoln died, thought I would save money). I've had one machine break (couple years ago; it happens), an it was replaced. All others, I have 6 now, but have owned many over 8 years, even the model you had.

People would not be here or buy if we were what "YOU" claim. And I guess that was not your last post.

Anyway, sorry you were disappointed, but I can assure most are not.