Printable View
So my helmet goes to shade #9 but that is too dark for some cuts.
I drew out some flames the other day on a sheet of Aluminum and had to cut them with no eye protection on so I could see the lines. not good, especially when my eyes are bad anyway.
Do they sell goggles in shades of .. 5, 6, 7 to use with Plasma cutting?
Dummy....you need eyes to clean a pool....
from hypertherm
Less than 40 amps.......shade 5
41-60 amps..................shade 6
61-300 amps................shade 8
http://www.eastwood.com/plasma-shade...FQhN4AodkHEAUQ
http://store.cyberweld.com/misaglsh5lew1.html
I bought some wrap around sunglasses in shade 5 from Zink Safety , They work good for cutting and grinding.
I use a face shield that supposedly has a shade 5 shield for cutting. Use a mechanics light if you can’t see that has helped me before.
Quote:
Originally Posted by sportbike
Thanks for the link, I like the Eastwood glasses... I Do Not suggest using a plasma cutter with no eye protection, I learned the stupid way
Having only one eye to begin with I take as few chances as possible ... when cutting I use a #9 but I bring out as much light as possible ... I use halogen spot lights or set up outside in the sun ... honest it works ... can see my outline and have good protection. The only time I don't use shade is when I'm coloring with acetylene and O2 even then I use shade till I have the flame set so it's not overly bright ... if I shade while doing the actual coloring I can't get the proper effect.
yes there goggles use for gas welding . i use my gas goggle when using plasma number 6 lence http://www.ebay.com/itm/Welders-Gogg...item3a6a5f5de5
I have several pairs of these "OTG" glasses which are great if you wear normal eyeglasses. They fit over normal eyewear and are available in different shades. Here's a link but be apprised, I have never ordered from this place. Only providing the link so you can see the product. http://www.envirosafetyproducts.com/...-shade5.0.html
I find these safety glasses to be very strong and do not scratch if you treat them with some care.
Thanks for the link!Quote:
Originally Posted by Ray C
That's a great idea, Winky. I was trying to get out of the heat over the weekend so I figured I'd resume welding after dinner. Good plan except while it is fine seeing the arc when it is lit, can't see enough of the material to start a good arc when the sun starts to go down! I'm going to get a spot light.Quote:
Originally Posted by Winky
I like the link from Ray C. Am also looking for some safety glasses that fit better over my prescriptions.
Good thread. Thanks everyone.
The LWS here had a face shield that was either 5 or 6, so I got it and couldn't be happier. No problems seeing the lines, especially in the daylight, and doesn't interfere with glasses either. I don't recall how much I paid, but it really wasn't out of line for a Huntsman.
Jackson has the same thing down here. #5 and #6 we have at the LWS and full face, they are nice. I have a friend that uses it for light MIG. They are about $22 for the Jackson. #5 is good for cutting and grinding (cutting=plasma)Quote:
Originally Posted by redbeard
I went to my LWS and they are ordering some OTG safety glasses for me.
I could probably get them cheaper online but these guys take care of me on gas and filler rods so it all equals out..
I have only used a plasma cutter a handful of times but have never used any shades.... after reading this I am guessing I probably should have.... Would standard sunglasses provide enough protection or should I invest in goggles?
Shane
Pick up some number 5 shades. You need them, sunglasses are not enough.Quote:
Originally Posted by ShaneJackson
Will do... actually I may already have some goggles that came with a acetylene torch (not shore of the shade...). A good pair of goggles are cheaper than a new set of eyes...
Shane
That's for sure on the eyes. The O/A set will work fine (probably a 4-5), they are a little less comfortable than the sun glass wrap around type.Quote:
Originally Posted by ShaneJackson
Another option is a full face shield and use it for O/A. plasma cutting and grinding with better skin and flying parts protection..
I only use genuine willy wonka plasma cutting goggles .Attachment 7542
Wouldn't an auto darkening helmet that has adjustable shade control from 6 to 13 work well for plasma cutting?
It could. 6 might be a little dark for some people. The grind mode of many are about 4 which can work, too, but is a little light, for most. How bright your surroundings are have an effect, too. Everyone is a little different. However, the helmets that have cutting modes to go from 3 or 4 to 8 or 9 will cover whatever you need. That's the great thing about adjustable shades. No more mixing sunglasses with #5 shaded face shield to get it just a little bit darker for some bright O/A work.Quote:
Originally Posted by X83
I agree, 6 is a bit dark "for me" as well. We have #5 glasses and #5 full face shields. The welding helmets are a little klunky for cutting and O/A "for me" as well. As Rambozo said, everyone is a little different. You need to find what works for you.
That's what I'm using ( Jackson ... lowest setting #9) which is probably why my method of bright lighting before the cut works for me ... I have little trouble seeing my mark however if I don't bring up the ambiant light I can't see worth beans.Quote:
Originally Posted by X83
When I first started out fitting steel I did not use dark cutting glasses when I used a cutting torch. I already where contacts and glasses, but in 3 months my eyes had gotten weaker and my prescription had to be increased by three power. In a year you might need to increase one or half power, and most years they stay the same. My eye doctor told me that a cutting torch and plasma cutter were hard on your eyes if you do not wear cutting glasses or goggles. Since then I always wear cutting glasses or a #5 face shield. It takes a little getting use to at first, but after a while you will not cut without them. I hate not being able to see when I am cutting.
Small price to pay to be able to see the rest of the time.Quote:
Originally Posted by SeanMurphy265