Where can I find docs for the CNC port on the back of the PP 256?
Thanks,
Andy
Printable View
Where can I find docs for the CNC port on the back of the PP 256?
Thanks,
Andy
Power Pro 256? It has a CNC port?
Does this look right?
http://weldingweb.com/showthread.php?t=55646
Even though it has the port, I think you'll regret fooling with it on that machine.
Parkour,
The connector pin layout looks the same. It would be nice to have the official docs though. I checked the PowerPlasma 60 manual, but it didn't document it either. Building at CNC router/plasma table is on my medium to long term want-to-do list. From looking at one of the plasma cutters linked on the torchmate site ( hypertherm 65 ), along with the link you provied, my guess is I'd provide a relay to start pins 1&2, and wait for the "ok-to-move" to close.
Mark,
Can you elaborate why I would regret it?
Thanks, Andy
The docs that came with the powerplasma60c had that image I linked to.. thats it.. nothing in the pdf manual.
I would love to know what you mean by that ? Why is the port there if it shouldn't be used ? How does the 60Amp output of the 256 make it different than the dedicated 60A plasma unit ?
I'm, obviously delighted to see the port there.
Thanks !
I will ask a still question : What is this port used for? My guess is torch control for CNC type welding?
It controls the plasma side only...though I personally don't recommend the unit be used but for the lightest CNC work only.
Hi Mark,
Hey, why would the capacity be different hand-held than during CNC work, if the feed speed is the same? You worried about the sustained load a CNC operation can have?
So occasional hobiest work on sheet metal would be ok, but not for production cutting of 3/4 inch plate?Quote:
Originally Posted by performance
The machine is 35% duty cycle...and the performance is not as good as a stand alone unit in plasma. CNC is always rated for half of what the standard hand held service is as well, no matter the brand.
I'd expect with the 256, you'd want to stay under 1/4" for CNC.
I would guess any brand combo machine is not really designed for any heavy fab work built mainly for hobby work.
The rule of thumb on CNC work is: 20 amps for every 1/8 inch of pierce on the metal, wanna punch through 1/2 inch, then you should have 80 amps. Cutting thicker is not the problem once you have a hole started.Quote:
Originally Posted by Andy
If your machine doesn't have enough amps to start a hole, you have to predrill or edge start.
Typically we consider 1/2 of the machines rated Quality Cut for a dedicated plasma. The 60C because of its start type pierces rapidly. The communication from Torchmate when they tested our unit was they were very please, if not surprised by the pierce speed of the 60C. The 60C has a 7/16" rating for CNC, but 1/2 shouldn't be much more of a hurdle.Quote:
Originally Posted by geezer
But the performance of the 256 plasma is not as strong as the 60...There are reasons for that, including shared duties of the unit. While its rated for 60 amps, amps are not all there is to cutting. It'll do a competent job on cutting most materials you'd come across every day, but it is NOT a production machine. That, we have made clear repeatedly. Its for portable repair, and for basic maintenance. It works fine, and the TIG is the strong point of the unit...and the plasma is in the support role, with many fine assists to win the game...but its not a game carrying player.
Mark, Thanks for the explanation / education. Now your reservations for PP256 plasma CNC use makes a lot more sense.
I have to agree with you , the 60C is a very good choice for most people, given the second rule of thumb for plasma: that is that the machine MAX output is generally 10 amps more than the breaker,,,so a 50 amp breaker which is what most people are wired for works out nicely for the 60C. In my case ,,my wireing is heavier than code and using a 60 amp breaker to pull 70 amps out of my PP80 is not a problem, if I wanted the full 80 amps I would probably hardwire into the 3 phase,,,I like the idea of having a machine that can pull the amps with ease,and have some reserve left over,that's why I chose the PP80.Quote:
Originally Posted by performance
Here in the US, the 80's are 1 phase only.
Re-phrase:
Do you have any guidance for connecting the PP256 to a CNC controller for light-duty plasma cutting?
Where has this been made clear ?Quote:
Originally Posted by performance
This is the first I've heard of this.Quote:
Its for portable repair, and for basic maintenance. It works fine, and the TIG is the strong point of the unit...and the plasma is in the support role, with many fine assists to win the game...but its not a game carrying player.
None of the Multi-Process units are suitable for efficient CNC applications . Due to the speed and time for many CNC applications you need both power and time for operating correctly. Having the limited Duty Cycle is detrimental to many CNC plasma applications
In fact for 2012 the CNC Port will be eliminated on al the multi units and will on be available on Plasma Cutters.
When adding it this year we thought that perhaps it might be good for the occasional limited use on smaller guage materials. The potential problem is that we can concievably have a Customer purchase board from inside.
Cheers