PM 256 Hi-Freq quit working

Printable View

07-03-2010, 07:55 PM
Tony_F

PM 256 Hi-Freq quit working

I had big plans this weekend to get caught up on projects, but no joy. I went to use the plasma cutter and the high frequency pilot arc did not work, I tried the TIG - no high frequency there either. I can start the both the plasma and TIG by scratching.

Its been about 3 weeks since I last used the machine and its unplugged when not in use. Machine was purchased new in April, is there anything I can do to fix it?

Thanks,

Tony
07-03-2010, 08:36 PM
performance

Tony,
You can call Mike and he should be able to walk you through diagosing it, and more than likely get you up and running.
07-03-2010, 08:50 PM
Tony_F

Quote:

Originally Posted by performance

Tony,
You can call Mike and he should be able to walk you through diagosing it, and more than likely get you up and running.

Thanks Mark, what number can I reach him at? I tried 650 588 8082 x203 and it went to voice mail - obviously on the weekend.

Tony
07-08-2010, 01:59 AM
Tony_F

I was able to get in touch with Mike, we adjusted the hi freq points at the front of the unit, they spark when the troch trigger is activated, but still no pilot arc or HF at the torch.
07-10-2010, 05:30 PM
Tony_F

Machine is on its way back to Everlast for an exchange. We'll see how long that takes, as they may be out of stock until later in the month.
07-10-2010, 06:31 PM
performance

Tony,

That shouldn't be a problem...By the time the machine is received, they should be able to ship it right out with no delay.
08-10-2010, 01:44 AM
Tony_F

Replacement Here!

I rec'd the replacement welder today, the box was in the usual condition, had a few tears on the side, but not totally squashed. The machine seemed fine. Anyway, the only function I had time to try was the plasma as I'm in need of it - it seemed to work OK - hi-freq is back! I'll post a few pictures of the project this weekend.

Thanks Mike and everyone for the support and getting it replaced.

Tony
08-12-2010, 05:03 AM
Slick

Quote:

Originally Posted by Tony_F

I rec'd the replacement welder today, the box was in the usual condition, had a few tears on the side, but not totally squashed. The machine seemed fine. Anyway, the only function I had time to try was the plasma as I'm in need of it - it seemed to work OK - hi-freq is back! I'll post a few pictures of the project this weekend.

Thanks Mike and everyone for the support and getting it replaced.

Tony

Good to hear! I like your initial review write up! I was curious what type of ball valves did you use for switching between air and argon?

I went to the local lowes, and they suggested using ones for natural gas, but the handles were too small.
08-19-2010, 10:12 PM
Tony_F

Quote:

Originally Posted by Slick

Good to hear! I like your initial review write up! I was curious what type of ball valves did you use for switching between air and argon?

I went to the local lowes, and they suggested using ones for natural gas, but the handles were too small.

Sorry Slick I just saw your question..

http://www.mcmaster.com/

- 4112T23 COMPACT HIGH-PRESSURE BRASS BALL VALVE, 1/4" NPT FEMALE X MALE, LEVER HANDLE
- 50785K72 MED-PRESSURE BRASS THRD PIPE FITTING, 1/4" PIPE SIZE, TEE
- 5346K16 BRASS BARBED HOSE FITTING, ADAPTER FOR 5/16" HOSE ID X 1/4" NPTF PIPE
- 50785K43 MED-PRESSURE BRASS THRD PIPE FITTING, 1/4" PIPE SIZE, MALE X FEMALE 90 DEG ELBOW
- 50785K12 MED-PRESSURE BRASS THRD PIPE FITTING, 1/4" PIPE SIZE, NIPPLE, 1-1/2" LENGTH