For Sale: 20pc. End Mill set Brand New

Printable View

04-24-2012, 06:31 PM
CGCINC

4 Attachment(s)

For Sale: 20pc. End Mill set Brand New

BRAND NEW...Two- and four-flute single end mills designed for slot, pocket, keyway and profile cutting.

•Center cutting design allows mills to be used as drills
•Made of titanium nitride-coated M2 high speed steel

3/8" shank: 3/16", 1/4", 5/16", 3/8" and 7/16" mill diameters
1/2" shank: 1/2" and 9/16" mill diameters
5/8" shank: 5/8" and 11/16" mill diameters
3/4" shank: 3/4" mill diameter

$60 plus shipping

I bought these for my drill press but they don't work.

Attachment 6336 Attachment 6335 Attachment 6337 Attachment 6338
04-25-2012, 12:19 AM
Finhead

If you take Paypal and shipping is resonable I'll take em. :) I'll pm you my address and info.
04-25-2012, 02:32 AM
CGCINC

Quote:

Originally Posted by Finhead

If you take Paypal and shipping is resonable I'll take em. :) I'll pm you my address and info.

I do take Paypal but I think shipping prices to Canada kill this deal!! :(
04-25-2012, 02:48 AM
Rodsmachineshop

lol I have the same set . there made good have had mine for about 6 months and use the heck out of them
04-25-2012, 06:18 AM
redbeard

If only there was some way to put a 5/8 and 3/4 collet into my mill:(, I'd be snapping them up.
04-25-2012, 06:58 AM
Finhead

Yeah shipping is a killer. :( Ah well like I said don't need em just handy to have a third set. :) My RF-45 is pretty easy on end mills anyway.

Quote:

Originally Posted by redbeard

If only there was some way to put a 5/8 and 3/4 collet into my mill:(, I'd be snapping them up.

What does your mill use? MT2-MT3? Shouldn't be a huge issue, might be a problem spinnning through anything other than brass or aluminum if your mill is small though.
http://www.grizzly.com/search/search...28114036919004
04-25-2012, 07:07 AM
Rodsmachineshop

http://www.grizzly.com/products/G9887 works good
04-25-2012, 07:14 AM
Finhead

I was actually saying he could buy an adaptor to up size to fit the 5/8 and 3/4 end mill shank. ;)

Quote:

Originally Posted by Rodsmachineshop

http://www.grizzly.com/products/G9887 works good
04-25-2012, 07:05 PM
Rivets

Quote:

Originally Posted by CGCINC

BRAND NEW...Two- and four-flute single end mills designed for slot, pocket, keyway and profile cutting.

•Center cutting design allows mills to be used as drills
•Made of titanium nitride-coated M2 high speed steel

3/8" shank: 3/16", 1/4", 5/16", 3/8" and 7/16" mill diameters
1/2" shank: 1/2" and 9/16" mill diameters
5/8" shank: 5/8" and 11/16" mill diameters
3/4" shank: 3/4" mill diameter

$60 plus shipping

I bought these for my drill press but they don't work.

Attachment 6336 Attachment 6335 Attachment 6337 Attachment 6338

CG,

I have the same sets.

Does the drill press chuck have a tendency to fall off when you mill?
If that is the issue, I have a solution.
Will share if there is any interest.

Cheers,
rivets
04-25-2012, 07:28 PM
CGCINC

Quote:

Originally Posted by Rivets

CG,

I have the same sets.

Does the drill press chuck have a tendency to fall off when you mill?
If that is the issue, I have a solution.
Will share if there is any interest.

Cheers,
rivets

Well, it did till I beat it up with a hammer! lol Still did it but not as bad.
I just couldn't get the mill to cut. I tried several speeds but I don't know what I'm doing so I'm going to wait till I get a real mill machine to figure it out.
I'm just cleaning my cabinets out and trimming the fat!!
04-25-2012, 09:43 PM
redbeard

Quote:

Originally Posted by Finhead

What does your mill use? MT2-MT3? Shouldn't be a huge issue, might be a problem spinnning through anything other than brass or aluminum if your mill is small though.
http://www.grizzly.com/search/search...28114036919004

MT2. I hadn't seen that style of mill holders when I went shopping before. Still looks like they only go up to 5/8 in a 2MT, but I'll have to do some more looking.
04-25-2012, 11:01 PM
X83

I'll take them, what's your Paypal and how much for shipping to FL?

I always find the 20-pieces sets in the square box and the rectangle boxes are hard to find.
04-25-2012, 11:16 PM
Finhead

This should coverr all your basses. I haven't bought those style holders yet (I run R8) but would like to since I know from using them on a buddies they are great and way fast for changeover of the same size shaft.
http://www.ebay.com/itm/NEW-7-PC-MOR...item5d31f516dc

Quote:

Originally Posted by redbeard

MT2. I hadn't seen that style of mill holders when I went shopping before. Still looks like they only go up to 5/8 in a 2MT, but I'll have to do some more looking.
04-25-2012, 11:19 PM
everlastsupport

Quote:

Originally Posted by X83

I'll take them, what's your Paypal and how much for shipping to FL?

I always find the 20-pieces sets in the square box and the rectangle boxes are hard to find.

I'm buying a Bridge Mill 2005 unit (some Cadillac sounding name far as the model; El Dorado I think). Was going to PM the same thing too you. "I have paypal. Price to Florida (post here)" if X83 does not like them, I have a drill press and will consider them and get a mill at some point.
04-25-2012, 11:42 PM
CGCINC

Quote:

Originally Posted by X83

I'll take them, what's your Paypal and how much for shipping to FL?

I always find the 20-pieces sets in the square box and the rectangle boxes are hard to find.

I sent you a PM
04-26-2012, 01:30 AM
X83

Quote:

Originally Posted by CGCINC

I sent you a PM

Paypal sent.

Thanks!
04-26-2012, 01:35 AM
Oleg

CG

I want 10% commission !!!!!

Oleg
04-26-2012, 01:39 AM
CGCINC

SOLD!

Quote:

CG

I want 10% commission !!!!!

Oleg

Your check's in the mail!! :D