Activity Stream - Welding Forums - Everlast Power Equipments Inc

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Today, 03:37 AM

DMAgunsmith started a thread New 210 EXT with issues in TIG Welding (GTAW/GTAW-P)

Well here?s the quick and dirty. Follow the manual for initial startup, aaand the fan run(s) continuously while the display never lights up. Wait...

0 replies | 5 view(s)

Today, 02:38 AM

SlowDave replied to a thread Problems with Imig 200e in MIG Welding (GMAW/GMAW-P/FCAW)

The light indicating power on on the front of the machine does light up when the machine is switched on. But nothing else except one click when I...

3 replies | 9 view(s)

Today, 02:18 AM

performance replied to a thread So What Do You Use Pulse TIG for? in TIG Welding (GTAW/GTAW-P)

It can be used for heat control OR for improving appearance of the weld, depending on the frequency and exact settings you choose. Consider pulse as...

1 replies | 38 view(s)

Today, 02:15 AM

performance replied to a thread Problems with Imig 200e in MIG Welding (GMAW/GMAW-P/FCAW)

Power switch if the display does not light as well.

3 replies | 9 view(s)

Today, 01:58 AM

SlowDave replied to a thread Problems with Imig 200e in MIG Welding (GMAW/GMAW-P/FCAW)

I will add that the fan has not come on since it shut down.

3 replies | 9 view(s)

Today, 01:56 AM

SlowDave started a thread Problems with Imig 200e in MIG Welding (GMAW/GMAW-P/FCAW)

I have had an I mig 200e for a little over 3 years. I also have Everlast stick and tig welders. I have been very pleased with all three. Last...

3 replies | 9 view(s)

08-03-2022, 05:36 PM

AZChuck started a thread So What Do You Use Pulse TIG for? in TIG Welding (GTAW/GTAW-P)

New to Forum, 10 months with 200DV and TIG, first post. Watched a gazillion YouTube videos. Weld almost entirely AL, rarely CRS and no stainless. I...

1 replies | 38 view(s)

07-16-2022, 08:07 PM

performance replied to a thread Power i-MIG 275P Flash, Loud Pop, and Tripped Breaker in MIG Welding (GMAW/GMAW-P/FCAW)

Have you called tech support yet? If you did, what did they say? This would be the best way to get this figured out. If you don't have the number,...

4 replies | 253 view(s)

07-16-2022, 06:48 PM

highplains replied to a thread Power i-MIG 275P Flash, Loud Pop, and Tripped Breaker in MIG Welding (GMAW/GMAW-P/FCAW)

4 replies | 253 view(s)

07-15-2022, 08:22 PM

highplains replied to a thread Power i-MIG 275P Flash, Loud Pop, and Tripped Breaker in MIG Welding (GMAW/GMAW-P/FCAW)

Thanks for the reply. I'll take the cover back off and try to get some additional pictures this evening. I've attached the original video that...

4 replies | 253 view(s)

07-15-2022, 06:41 PM

Nanoqx replied to a thread Power i-MIG 275P Flash, Loud Pop, and Tripped Breaker in MIG Welding (GMAW/GMAW-P/FCAW)

highplains, the picture you sent is low quality and you didn't say or show where you might be seeing any damage on the board. Can you repost better...

4 replies | 253 view(s)

07-11-2022, 09:09 PM

Franks created a blog entry Gun control in the United States in Franks

0 replies | 0 view(s)

07-11-2022, 09:05 PM

Franks created a blog entry Gun control in the United States in Franks

0 replies | 0 view(s)

07-11-2022, 01:46 AM

Fallen Tree replied to a thread MTS 275 problem in MIG Welding (GMAW/GMAW-P/FCAW)

I found the problem, the guard that covers the bottom drive gear was rubbing on the drive rolls. I was changing to an 0.45 wire and when changing the...

3 replies | 223 view(s)

07-10-2022, 07:02 PM

turbotom1052 replied to a thread New Pedal - 200DX in TIG Welding (GTAW/GTAW-P)

Was it the covid that tore up your ankles and knees, or was it all the walking around we all had to do to find places that were still open and doing...

4 replies | 1803 view(s)

07-10-2022, 02:10 PM

highplains started a thread Power i-MIG 275P Flash, Loud Pop, and Tripped Breaker in MIG Welding (GMAW/GMAW-P/FCAW)

I'm looking for advice on whether it's feasible to have my Power i-MIG 275P repaired. I purchased it almost exactly 6 years ago and have used it...

4 replies | 253 view(s)

07-10-2022, 12:52 AM

Fallen Tree replied to a thread MTS 275 problem in MIG Welding (GMAW/GMAW-P/FCAW)

I think the video is misleading at times the cup was almost touching the plate and generally not over 1/2" away. I was trying to walk the cup more...

3 replies | 223 view(s)

07-09-2022, 07:04 PM

performance replied to a thread MTS 275 problem in MIG Welding (GMAW/GMAW-P/FCAW)

Seeing the video, it looks like you are an 1 or more away. It definitely is too far off now. If you have an extra hand, have someone take a look at...

3 replies | 223 view(s)

07-09-2022, 01:50 PM

Fallen Tree started a thread MTS 275 problem in MIG Welding (GMAW/GMAW-P/FCAW)

I recently purchased a MTS 275 that has an intermittent problem, it does seem to be becoming more frequent. I'm welding 14ga 1 1/4" tubing with .030...

3 replies | 223 view(s)