Register
Help
Remember Me?
Home
Forum
Our Products
What's New?
Activity Stream
New Posts
New Articles
New Events
New Blog Entries
Mark Forums Read
Blogs
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You will have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 24 Hours
Last 24 Hours
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Articles
Articles
Blog
Blogs
Filter by:
Last 7 Days
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Yesterday,
11:34 PM
lablacksmith
started a thread
pay shipping both ways under warranty
in
Customer Testimonials
After working with tech support since March finally got somebody to listen, pull trigger air flows but no plasma. as I said got RMA and since it's...
see more
0 replies | 4 view(s)
Yesterday,
06:08 PM
christian
replied to a thread
Dead old '2 knob' 240 volt only 210EXT
in
TIG Welding (GTAW/GTAW-P)
Call, Everlast, Their phone tech service may not be contingent on the warrantee length. I mean, Mark, from Everlast, monitors this forum and...
see more
1 replies | 16 view(s)
Yesterday,
01:25 AM
GaveUpOnTV
started a thread
Dead old '2 knob' 240 volt only 210EXT
in
TIG Welding (GTAW/GTAW-P)
Hi, I haven't used my tig machine 210EXT in a couple of years. When I attempted to, I could not strike an arc. The high frequency works well, but...
see more
1 replies | 16 view(s)
01-15-2021,
07:19 PM
broberts5
started a thread
My sweet 250EX has gone on siesta...
in
TIG Welding (GTAW/GTAW-P)
I was welding with my 250EX an lost high freq. so I uncovered it, adjusted points. Great! Back to welding beautifully! After about an hour, it...
see more
0 replies | 21 view(s)
01-15-2021,
06:21 PM
christian
replied to a thread
Which Everlast?
in
MIG Welding (GMAW/GMAW-P/FCAW)
Yeah, I wouldn't recommend any 115V MIG unit, especially a heavy transformer one, as it may not give you it's full rated output without a 30 amp...
see more
1 replies | 27 view(s)
01-14-2021,
03:36 PM
Bramic71
started a thread
Which Everlast?
in
MIG Welding (GMAW/GMAW-P/FCAW)
Hello. I am new to welding and looking at getting my first welder. I was looking at purchasing a Hobart HH140, then I saw videos on the Everlast...
see more
1 replies | 27 view(s)
01-12-2021,
07:23 AM
ALO604
started a thread
Hose quality
in
General Welder Questions
How durable are the newer orange torch lines? Do they still need to be wrapped?
see more
0 replies | 28 view(s)
01-12-2021,
04:08 AM
Accelo
started a thread
PowerPro256 Broken
in
Multi-Process Units (TIG,Stick,Plasma/MIG,TIG,Stick Combo units)
After some soul searching and being informed repairs will take 30 to 40 days I have decided to sell my welder in its current condition (broken) I...
see more
0 replies | 26 view(s)
01-11-2021,
12:27 AM
performance
replied to a thread
Propylene Glycol Antifreeze for Welder Coolants
in
TIG Welding (GTAW/GTAW-P)
IF a customer wants to keep their warranty in effect, then they should follow our advice. You can bet and suppose a lot here. Fine, but when it...
see more
10 replies | 253 view(s)
01-11-2021,
12:24 AM
performance
replied to a thread
Machine selection advice
in
TIG Welding (GTAW/GTAW-P)
I'm sorry MC5W. But lets not revive 5 year old threads. Inverter welders can use lower amperages because of Arc force, but that will depend upon...
see more
20 replies | 5864 view(s)
01-11-2021,
12:19 AM
performance
replied to a thread
AC welding setup
in
TIG Welding (GTAW/GTAW-P)
No. The torch stays in the negative for all TIG operation. Download your manual from the website. It is up on it. It covers pretty much everything...
see more
1 replies | 20 view(s)
01-11-2021,
12:17 AM
performance
replied to a thread
Help: lightning MTS 275 not feeding (video)
in
MIG Welding (GMAW/GMAW-P/FCAW)
Spot settings will get you everytime.
see more
4 replies | 75 view(s)
01-11-2021,
12:15 AM
performance
replied to a thread
275P pulse settings? and spatter in mig mode?
in
MIG Welding (GMAW/GMAW-P/FCAW)
Inductance 75%. Start there. The results will vary based off the user's experience in setting a manual pulse. The 350P is a type of synergic pulse....
see more
1 replies | 25 view(s)
01-10-2021,
08:39 PM
ALO604
started a thread
AC welding setup
in
TIG Welding (GTAW/GTAW-P)
I have just received my 200DX. Never welded with AC before, only DC steel. Do I need to switch cables around or does the machine take care of...
see more
1 replies | 20 view(s)
More Activity
No More Results
No Recent Activity