Search:

Thinking about putting a Flex Loc 230 torch on the 250ex, anybody got one or know how good they are? Main questions I have, does the swivel torch stay tight and with no water running through the head...

Will the ZHCK-W from Arc Zone fit the newer water coolers? It converts the 5/8 left hand water line to quick release.

Thinking of adding a PT185 for the convenience of 110 in parts of the shop. Does the foot control still override the panel amperage?

Does the machine have enough post flow for high amperage welds?

My first 250EX was bought used, it was owned by a guy who worked on all brands of welders. He said the 250EX was not welding at factory specs, it would not pulse at .2pps and would not weld at 10...

The number one question is, will the 210EXT hold a sharp tungsten (red) at high amperage and not get dingle berries on AC? The 250EX will do this only after the AC balance potentiometer has been...

If I weld 8 hours with the Syncrowave 250 on AC, the high frequency is on for 8 hours. If I weld 8 hours on the 250EX, the high frequency is on total of about 4 minutes. That is why the newer welders...

It's true that other welders have more heavy-duty points. Some people say the points erode over time, but I have never had to adjust any of my Miller or Everlast machines. The light weight points...

ccccccccccccccc

ccccccccccccccc

ccccccccccccccc

ccccccccccccccc

One thing I have figured out after getting the PP70 (A81 torch), it's best to get the amperage close to what you will be cutting the most. The smallest tips for the 70 amp plasma is 1.0mm. For 19...

That milling machine coolant really stinks don't it? I hand wash all of my machined parts with soap and hot water before welding.

Yea, the pulser frequency and AC balance potentiometers have both been replaced by 1 meg pots. Actually they ohm out at 1100K. The older 250EX has been modified for 2.5 years and the new one for...

No, but it will adjust down to no etched or visible cleaning action. Even turned all the way down, it has plenty enough cleaning action to leave beautiful welds on aluminum. The arc is very focused...

After reading some of Todd's posts, the 250EXT pulse has been bumped to 500pps on AC, If the AC frequency is bumped up to 250 hertz or higher, I would consider getting one. The 315EXT only being...

I use 5356 to weld 6061 to 6063, 4043 does not weld all that good to me on 6061. I have repeatedly tried 4043 on both the Syncrowave 250 and the 250 EX, never being completely satisfied with the...

Not one technical question I have ever asked has been answered by Everlast, other members have helped me out a lot. What's up with that?

That's a good idea, thanks

Got a chance to look at the cooler today, it has one shaft turning the fan and the other turns the pump. The motor was a little hard to turn, the pump was in a little bit of a bind, I loosened the...

The voltage on the back of the 250EX is 240, By looking through the vent holes, I think the electric motor has one shaft out each side, one turns the pump and the other has a fan bolted on. Again...

I probably brag more about the 250EX than most, Our first 250Ex was bought used and had been tuned up by a local shop to weld at specs, It had different resistance pots on the pulser and ac balance....

Its a Everlast 7 months old, plugged into the back of a 250EX. Whats weird is the light on the switch comes on a minute before it starts working. And the welder works just fine.

My water cooler is slow to start pumping and for the fan to start working, The light comes on but it takes about a minute every time to actually start working. Any clues on what I should check first?...

I agree on using a mig everywhere I can but on not on anything round. If you have a mig with twin pulse, you should post some pics.

I demoed a Fronius synergic mig set up for aluminum with twin...