Search:

If it was the points, though, wouldnt it affect the performance also with the torch switch? From what I recall, it seemed to work just fine with the torch switch in both 2t and 4t. Does the points...

Thanks Mike. I didnt get the chance to get back to it yet but I will. From your post, it sounds like its the pedal and so I need to open it and check a few things. Ill call in before I mess with...

Meh scroo those guys...if Miller and Lincoln want to stay relevant, they should bring their prices down. While the whole 'made in America' theme is noble and patriotic in a sense, when actually...

My PowerPlasma 50 and 30 pc consumable kit came about two weeks ago and I was missing the stand-off for the S45 torch and two of the torch cups...after an email a few days ago (I was tempted not even...

Once again, some gorgeous work, Donor.

Extremely envious of your diverse talents!

For the record, without distortion or over-melting of the pieces, I secured a 5/16" soft steel ball to a piece of 1/8" steel rod (at about 22 amps), and a 1/4" soft steel ball to a piece of .080"...

I finally got the chance to try out the 200DX yesterday. The amperage knob seems to be just fine, actually - amperage display from 5 to 202 amps - cant ask for much more than that. However, I am...

Great thanks for the information, Duncan - it sounds like a quality full-featured little unit. Will this unit be available in the states and will it be added to the website(s) any time soon?

This is a repeat post - have one in the plasma cutter section which may or may not be more appropriate.

A 25 amp 110v Everlast plasma cutter was mentioned in another thread by Duncan, I believe. ...

Just to add - I tried some lower psi settings last night and it really didnt seem to affect anything when doing the thinner stuff. I only tried a couple of test cuts, though, so maybe a little more...

Yeah Ill have to play around with it some more, Rod. Im curious to try the lower pressure based on the info Mike had heard, too, regarding sheet metal cutting. On anything 1/8" and under, it seemed...

Ill try decreasing the air pressure and see how that behaves...at low amps (20), this wont be too rough on the consumables, will it?

On another thread, a 25 amp Everlast unit was mentioned as being sold in Canada. Can Oleg or Duncan give us some more details on this unit? Im sure are many on these boards that would like to hear...

Thanks for the feedback, guys...unfortunately I didnt get the chance to get to the 200DX trials (I did get the plug wired up, though). I was busy getting my new shop compressor set up - oil change,...

I got my pp50 hooked up and was slicing through some stuff like butter yesterday...wicked cool machine. :D I cut a few different thicknesses of steel sheet steel up to 1/8", some 1/8" aluminum, then...

hahaha I know I know

The amperage knob on my new 200DX seems excessively loose...far more so than any of the other smaller knobs...to the point even that I cant envision it engaging the pot, as it seems there should be...

Thanks for the help. I went with the PP50 and it should be here any day now!

Thanks guys...went with the 200DX and a PP50 and they should be here in the next two days!

Red and Rod...thanks...thats the kind of stuff I was looking for.

But still want to know more about the pp25!

Titan Winch or Everlast support...where can I find more info and pricing on the pp25 unit and its availability in the states? I did not see anything on Everlast Canada site?

Thanks for the responses, guys...PowerPlasma 25???

Where can I find the specs on this unit and why is there no info on the site about it? (apologies if I missed it)

Im very curious to know...

Ill be cutting mostly 3/16" and under, but would sometimes want a clean cuts on 1/4", and maybe 1/2"+ a wee bit severance.

How does the PP50 perform on minimum amp settings (20 is the min, yes?)...

Oooooo...Im excited :D

thanks for the info, TW.

Will there be any price change on the 200DX with the newer pre-flow and foot pedal max amps adjustable at the panel?

Are these units available in the U.S. at this time?

Thanks.