contact us: 1-877-755-weld(9353) DEALERS WANTED | Terms & Policy
Welder
Welder Home
Search our site
Welder
Welding equipments Everlast Forum Home Contact everlast Everlast FAQ
Welcome to everlast power equipment. Your one stop source for reliable welding and plasma cutting equipments http://www.everlastwelders.ca http://www.everlastwelds.com.au http://www.everlastwelds.eu
  • Welders Home
  • Multi Purpose Units
  • PowerUltra 250P
    		•  Bookmark and Share

    PowerUltra 250P:

     
    PowerUltra Series DC IGBT based Inverter: 250 Amp DC Pulse TIG/ 200 Amp DC Stick Welder/ 50 Amp Plasma Cutter
    Processes: GTAW-P, SMAW, PAC

    IMPORTANT PRODUCT NOTES: While under foot pedal control, the maximum amps are not limited on the panel. The foot pedal controls the full range of amps, from 5 to 250 amps. Although the pedal can control the amps through varying the pedal position, no lower maximum amps than 250 may be set.
    The pulse is preset to offer simple pulse control of the TIG with two basic settings: .5 Hz, and 25 Hz.(specification subject to change)

    The PowerUltra 250P is an entry level DC output multi-purpose welder/cutter and cannot weld aluminum! However, it can be used to cut aluminum. For work requiring aluminum welding and cutting, see our PowerPro units.

    TO SWAP BETWEEN PROCESSES, CABLES AND GAS LINE SUPPLY CHANGES MUST BE MADE. THE UNIT CANNOT OPERATE MULTIPLE PROCESSES SIMULTANEOUSLY.
     
    PowerUltra 250P

    PowerUltra 250P




          
    		 Features & Benefits
    - All-in-one portability is good choice for portable repair operations
    - Compact design allows the unit to go anywhere
    -Straight forward controls, with two preset pulse settings for easy TIG operation.
    - Quick change out of torches for easy change from TIG to plasma back to TIG.
    - Low power consumption due to inverter design.
    - High duty cycle of 60% at rated amperages for TIG/Stick/Plasma.
    - Front air pressure gauge for easy verification of air pressure.
    - Over Current/Duty cycle protection circuit warns and interrupts welding/cutting to ensure safe, and long life operation.
    - Clean and smooth plasma cuts on virtually any metal.
    - Welds Steel, Stainless Steel and Titanium (The PowerUltra is DC output only, and is not suitable for welding Aluminum, although it can cut aluminum.)
    - Great arc stability for TIG/Stick functions due to IGBT inverter design.
    - 2 preset pulse settings. (.5 and 25 Hz)
    Dual voltage design allows unit to be operated on 120V or 240V. (Output is reduced in 120V operation to approximately 110 amps TIG/ 95 amps Stick/25 amps plasma.)

    NOTE: For use with generators, this welder requires a MINIMUM of 10,500 watts of continuous output and be designated as "clean power" by the generator manufacturer. For best results, a higher output generator may be required. Use with generators not designated by the generator manufacturer as a "clean" power source may void warranty.



























    Not recommended for stick operation with E6010.


    Make an offer for PowerUltra 250P  


    Price : $999.99
    Recommended Areas Of Use
    • Recommended for use in areas where multiple processes are required for on-the-spot repairs.
    • Good choice for use at the track for motorsports repairs of steel and stainless.
    • Overall an excellent choice for a business with space limitations or a portable repair business not requiring production or intensive fabrication work.
    The PowerUltra 250P is a good all around performer for heavy construction equipment repairs.
    Standard Equipment
    -12 ft. economy, Water-Cooled Series WP 18 Torch
    - Foot Pedal
    - Consumable Starter Kit
    - Argon Regulator
    - Air Pressure Regulator
    - Air Pressure Gauge
    - Water Trap
    - SMAW (Stick) electrode holder
    - 6ft power input cable. (Recommended NEMA 6-50 power plug to be supplied by customer. No plug included.)
    Consumable starter pack for TIG and Plasma. Tungsten is not included for TIG
    - Work Clamp with cable
    - 12ft. S-45 series plasma torch uses consumables compatible with several brands.

    NOTE: Extra inline air dryer is required for proper plasma operation. Water trap is not to be used as sole dryer.
    Optional Equipment
    - Water cooler
    - Welding helmet
    with special #7 shade for cutting with up to #15 shade for TIG
    - Welding cart
    - Consumable Kit
    - Deluxe, WP series, 9,17, and 26 (suggested appropriate sizes) compatible TIG torches available in 15ft and 25ft lengths.
    Recommended Metals
    Steel, Stainless, Copper, Titanium.
    NOTE: The PowerUltra 205 is a DC output only welder. It is not suitable for use in welding Aluminum.
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 250P
    PowerUltra 164
    PowerUltra 185
    PowerUltra 205
    PowerUltra 250P
    PowerUltra 164 PowerUltra 185 PowerUltra 205 PowerUltra 250P
    Over Current Warning Yes Yes Yes Yes
    Voltage 120-240V 1PH 120-240V 1PH 120-240V 1PH 120-240V 1PH
    Max Start Input Amps 27 @ 220V 31.3 @ 220V (due to plasma requirements) 31.3A @ 220V 45A @ 220V
    Max Running Amps 23 @ 220V 25 @ 220V 25A @220V 36A @ 220V
    TIG (GTAW) Rated Amps @ Duty Cycle 60%@160 A 60%@180 A 60%@200 A 35% @ 250 A
    Start Amps(Initial) None None None None
    End Amps(Final) None None None None
    Arc Force Control(DIG) None None None None
    Up Slope Timer None None None None
    Down Slope Timer None None None None
    Plasma (PAC) Rated Amps @ 60% Duty Cycle 40 A 50 A 50 A 50 A
    Pulse Frequency Control Fixed, High/Low Fixed, High/Low Fixed, High/Low Fixed, High/Low
    Pulse Time On(Width) Fixed Fixed Fixed Fixed
    Pulse Amp Ratio Fixed Fixed Fixed Fixed
    Lift Start Tig No No No No
    High Frequency Start Yes Yes Yes Yes
    4t/2t Remote Panel/Remote Only Panel/Remote Only Panel/Remote Only Panel/Remote only
    AC Frequency Control None None None None
    AC Balance Control None None None None
    AC Square Wave(Aluminium) No No No No
    Pre-Gas Flow Timer None None None None
    Post Flow Timer(seconds) 1 - 25 1 - 25 1 - 25 1-25
    Stick (SMAW) Rated Amps @ Duty Cycle 35% @ 160 A 35% @ 180 A 35% @ 200 A 35% @ 200 A
    Shipping Weight 55 lbs 60lbs 67 lb 67 lb

    The EVERLAST PowerUltra offers maximum portability and performance. The unit's IGBT inverter produces a pure and stable DC arc, handling any tough stainless steel or steel welding.

    There are no complicated controls or cumbersome menus. Simply turn the unit on, select for TIG operation and start welding. For the plasma cutting function, just change the torches and lines, so you can start cutting.[read more...]
    Visa Mastercard American Express Discover eCheck PayPal
    Copyright 2004 - 2011 Everlast Power Equipment Inc. All Rights Reserved.

     

    Diesel Generators | Multi-Purpose Units | Plasma Cutters | Welders | TIG Water Coolers | Welding Helmets | Consumables | Spare Parts | Accessories
    Welders Word Press | Welders News | Sitemap | Welder Blog | Welding Equipment Blogspot | Welding Supply Articles | Welding Calculators
    Welding Symbols | Welding Terms | Welding Terms Finder | Welders Schools


    While welding is a valuable skill to possess, it is important to get the right machine to do the job. If you are a professional or a hobbyist and are trying to find the machine to fit your needs, Everlast can help. We offer a full line of welders for the hobbyist and professionals, including MIG, TIG, STICK and plasma cutters. We are proud to feature IGBT components and modules from Siemens for long life service whether in the field, in the shop or in the home. Don't forget about our line of silent diesel generators and engine drive welders. We offer convenient ordering capability without leaving your home or office.